Manual Parkside IAN 49374 PSB 1050 A1 (page 41 of 55) (English, Portuguese, Spanish)

744937

Zoom out

Zoom in

1/55

41 GB/MT

Assembly tools for screws and nuts:

j When using screwdriver bits, always use a

universal bit holder.

j To screw things in, always switch the changeover

switch “drill / percussion drill”

to the right to

position

Fitting / using the dust

extraction device

j Only use the dust extraction device when work-

ing on cement, brick and building stone. Wood

or plastic shavings could easily lead to the de-

vice becoming blocked.

ATTENTION! FIRE HAZARD! Do not work

on any metal materials when you have ﬁtted

the dust extraction device. Hot metal ﬁlings could

set parts of the dust extraction device on ﬁre.

NOTE: The dust extraction device

can only be

ﬁtted to the additional handle

if the depth stop

has previously been removed. If need be, loosen

the wing screw

by turning it anti - clockwise and

remove the depth stop

. Attach it again after

you have ﬁtted the dust extraction device

and

tighten the wing screw

again.

j Loosen the sing screw

and place the dust

extraction device

precisely onto the addi-

tional handle

j Tighten the wing screw

by turning it clock-

wise.

j You should preferably use a workshop vacuum

cleaner for dust extraction purposes. Connect

the tube of the dust extraction device with the

angle adapter

; see also Figure F.

NOTE: We recommend the use of a dust ex-

traction device

up to a drill size of 13 mm.

j If it is necessary to use the reducer piece

push the reducer piece into the adapter for ex-

ternal vacuum extraction

j To dismantle, proceed in reverse order to what

is described above.

First use

Switching on and oﬀ

When operating the hammer - action drill you can

select between intermittent or continuous operation

mode.

To switch on intermittent operation mode:

j Press the ON / OFF switch

To switch off intermittent operation mode:

j Release the ON / OFF switch

Switching continuous operation on:

j Press and hold the ON / OFF switch

down

and press the locking button

To switch off continuous operation mode:

j Press and then release the ON / OFF switch

Pre - selecting the

rotational speed

With the handwheel for speed preselection

you can pre - select the rotational speed in steps.

j The rotational speed that is suitable depends

on the material that has to be processed. We

recommend you carry out tests ﬁrst to deter-

mine the best rotational speed.

Tip: These two basic rules with regard to rota-

tional speed will, however, always help you:

1. large drill diameter = lower rotational speed

and so a smaller drill diameter = higher rota-

tional speed

2. harder material = lower rotational speed

Inﬁnitely variable adjustment

of the rotational speed

The ON / OFF switch

has a variable speed

control device. Slight pressure on the ON / OFF

switch

will bring about a low rotational speed.

The rotational speed will increase the more pres-

sure you exert.

Before first use / First use

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 49374 PSB 1050 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 2,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 49374 PSB 1050 A1

Parkside IAN 49374 PSB 1050 A1 User Manual - German, Dutch, French, Italian - 45 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 49374 PSB 1050 A1 Manual

Product: