749290
20
Zoom out
Zoom in
Previous page
1/75
Next page
PSTK 800 B2
16 GBIE
Initial operation
Fitting/changing the saw blade
Always remove the plug from the power socket
before working on the appliance.
Remove the pivoting guard .
Turn the quick-release chuck and hold it in
this position.
Press the required saw blade into the quick-
release chuck as far as the limit stop.
Release the quick-release chuck – it must
return to its initial position. The saw blade is
now locked.
WARNING! The saw blade teeth must point
forwards at this point (see foldout page)!
Replace the pivoting guard back onto the
device.
Fitting the guide fence
The guide fence can be fitted on the left or
right of the appliance.
Undo both of the clamping screws on the
insertion openings .
Push the guide fence into the insertion
openings .
NOTE
The two respective marking arrows indicate
the cutting width.
Retighten the two locking screws.
Connecting the sawdust extraction
appliance
Push the reducer into the extraction connector
until it is secured.
Attach an approved dust and sawdust extractor
to the reducer or extraction connector
directly.
Fitting the splinter guard
The splinter guard can prevent the tearing up of
the surface when sawing wood. The splinter guard
can only be used with certain sawblade types
and only at a cutting angle of 0°.
Press the splinter guard into the sliding shoe
from below (arrow facing upwards).
Operation
Setting the cutting angle
Push the clamping lever forward and pull the
baseplate to the front.
Adjust the cutting angle to 0°/ 22,5°/ 45° with
the aid of the markings on the baseplate .
Push the baseplate to the rear so that the
locking pin engages in the toothing .
Push the clamping lever backwards.
NOTE
With a cutting angle of 22,5°/ 45°, the piv-
oting guard must be removed beforehand!
If the baseplate cannot be locked well by
clamping lever , remove the extraction con-
nector , then tighten the clamping screw
with hex key.
Setting the stroke rate
Use the stroke rate preselection adjusting
wheel to set the required stroke rate.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 312018 PSTK 800 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 312018 PSTK 800 B2 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info