749331
18
Zoom out
Zoom in
Previous page
1/68
Next page
PET 25 C2 GBIE 15
Appliance-specific safety
instructions for electric staple
guns
Always check that the power tool contains
staples.
Careless handling of the staple gun can lead
to unexpected ejection of staples which could
cause injuries.
Never aim the power tool at yourself or other
people in the vicinity. Unintended triggering
will cause a staple to shoot out, which can lead
to injuries.
Do not activate the power tool until it is
pressed firmly against the workpiece. If the
power tool is not in contact with the workpiece
the staple can rebound off the fastening point.
Disconnect the power tool from the mains or
battery if a staple becomes jammed in the
power tool. If the staple gun is connected to a
power source, it could be unintentionally acti-
vated while removing a jammed staple.
Be careful when removing a jammed staple.
The system may be live and the staple could be
forcefully ejected while you are attempting to
unblock the jam.
Never use this staple gun for fastening electri-
cal cables. It is not suitable for the installation
of electrical lines, can damage the insulation
of electrical cables and thus cause electrical
shocks and increase the risk of fire.
WARNING!
To avoid risks, damaged mains cables of
the appliance should be replaced by the
manufacturer or the manufacturer’s customer
service department or a similarly qualified
person.
Before use
NOTE
Only fill the magazine when the appliance is
switched off! Set the ON/OFF switch to
the position "0" and pull out the plug!
Filling the magazine
Squeeze the magazine slider (see fig. A).
Pull the magazine slider out of the magazine
of the appliance (see fig. B).
Fill the magazine with staples or nails (see
fig. C).
After filling, push the magazine slider back
into the magazine as far as the stop and you
hear and feel it click into place.
NOTE
When filling with nails, use the right shaft
(as shown in fig. C). Ensure that the nail
heads are always at the top.
Note the maximum fill level of approx.
85 staples or approx. 75 nails.
The fill level indicator shows whether the
magazine still contains staples or nails.
Setting the impact force
NOTE
Select the lowest impact force sufficient for
stapling. Take into account the length of the
staples or nails you are using as well as hard-
ness of the material you are working with.
Impact force control
Increasing the impact force:
Turn the impact force control anticlockwise.
Reducing the impact force:
Turn the impact force control clockwise.
IB_310956_PET25C2_LB8.indb 15 10.12.18 13:31
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 310956 PET 25 C2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 310956 PET 25 C2 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info