748151

Parkside IAN 303408 PBS 350 A1 Manual

29
Zoom out
Zoom in
Previous page
1/72
Next page
22 GB/IE
15. Troubleshooting
Fault Possible cause Remedy
Motor does not work Motor, cable or plug defective, fuses burnt
Housing cover open (limit switch)
Arrange for inspection of the machine by a
specialist. Never repair the motor yourself. Danger!
Check fuses and replace as necessary
Close housing cover exactly
The motor starts up
slowly and does not
reach operating speed.
Voltage too low, coils damaged, capacitor burnt Contact the utility provider to check the voltage.
Arrange for inspection of the motor by a specialist.
Arrange for replacement of the capacitor by a special-
ist
Motor makes excessive
noise
Coils damaged, motor defective Arrange for inspection of the motor by a specialist
The motor does not
reach its full power.
Circuits in the network are overloaded (lamps
other motors, etc.)
Do not use any other equipment or motors on the same
circuit
Motor overheats easily. Overloading of the motor, insufficient cooling of
the motor
Avoid overloading the motor while cutting, remove dust
from the motor in order to ensure optimal cooling of the
motor
Saw cut is rough or
wavy
Saw blade dull, tooth shape not appropriate for
the material thickness
Resharpen saw blade and/or use suitable saw blade
Workpiece pulls away
and/or splinters
Excessive cutting pressure and/or saw blade not
suitable for use
Insert suitable saw blade
Saw blade is not running
straight
a) Guide has been wrongly set
b) Wrong saw blade
a) Set the saw blade guide according to the operating
instructions
b) Select a saw blade according to the operating
instructions
Burn marks appear on the
wood during the cutting
work
a) Blunt saw blade
b) Wrong saw blade
a) Change the saw blade
b) Select a saw blade according to the operating
instructions
Saw blade jams during
cutting work
a) Blunt saw blade
b) Deposits on the saw blade
c) Guide has been set poorly
a) Change the saw blade
b) Clean the saw blade
c) Set the saw blade guide according to the operating
instructions
Service information
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also
required for use as consumables.
Wear parts*: Bandsaw blade, table inserts, Push stick
* Not necessarily included in the scope of delivery!
By properly disposing of this product, you are also contribut-
ing to the effective use of natural resources. You can obtain
information on collection points for waste equipment from
your municipal administration, public waste disposal author-
ity, an authorised body for the disposal of waste electrical
and electronic equipment or your waste disposal company.
14. Transport
The machine must only be lifted and transported on its frame
or the frame plate. Never lift the machine at the safety de-
vices, the adjusting levers, or the sawing table.
During the transport the saw blade protection must be in the
lowest position and near the table.
Never raise at the table! Unplug the machine from the mains
during transport.
… 29 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-ian-303408-pbs-350-a1

Reset search

  • Hallo sehr geehrte Damen und Herren, ich suche einen Ersatz für die Bandsäge.
    Einmal das Sägeblatt und zum anderen Die Bandauflage für die zwei Rollen.
    Vielen Dank im Voraus. Submitted on 19-7-2022 at 10:02

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 303408 PBS 350 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 303408 PBS 350 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info