Manual Parkside IAN 303408 PBS 350 A1 (page 26 of 72) (English, German, Dutch, French)

748151

Zoom out

Zoom in

1/72

19GB/IE

• A wide saw band is used if a straight cut is required. This is

important in particular when cutting wood. The saw band

has a tendency to follow the wood grain and therefore

deviates easily from the desired cutting line.

• Fine-toothed saw bands cut more smoothly, but also more

slowly than coarse saw bands.

Attention: Never use bent or torn saw bands!

8.8 Replacing the saw band (Fig. 1a+1b+14)

• Set the saw band guide (5) at approx. half height between

the saw table (7) and machine frame (15).

• Undo the cover locking mechanisms (10) and open the

side covers (11).

• Remove U-reinforcement (34) as described in 8.1.

• Relieve the Bandsaw blade (21) tension by turning the

clamping screw (1) anti-clockwise.

• Remove the Bandsaw blade (21) from the saw band rollers

(2+8) and through the slot in the saw table (7).

• Place the new Bandsaw blade (21) centrally on both saw

band rollers (2+8). The teeth of the Bandsaw blade (21)

must point downwards in the direction of the saw table

(Fig. 6).

• Tension the Bandsaw blade (21) (see 8.2)

• Close the side cover (11) again.

• Re-install the U-reinforcement (34).

8.9 Replacing the table insert (Fig. 13)

In case of wear or damage, the table insert (6) must be re-

placed; otherwise there is an increased risk of injury.

• Remove the worn table insert (6) by lifting it up and out.

• Installation of the new table insert takes place in reverse

order.

8.10 Extraction nozzle (Fig. 1b)

The band saw is equipped with an extraction nozzle (19) Ø

40 mm for chips.

Only operate the device with a suitable extraction system.

Check and clean the suction channels at regular intervals.

8.11 Push Stick retainer (Fig. 12)

The Push Stick retainer (48) is pre-mounted on the machine

frame. If unused, the Push stick (26) must always be stowed

in the Push Stick retainer.

9. Operation

9.1 On/Oﬀ switch (12) (Fig. 15)

• To turn the machine on, press the green button „I“.

• To turn the machine off again, press the red button „0“.

• The band saw is equipped with an undervoltage switch.

With a power failure, the band saw must be switched back

on again.

9.2 Parallel stop (Fig. 16)

• Press the clamping bar (25) of the parallel stop (24) up-

wards

• Slide the parallel stop (24) left or right of the Bandsaw

blade (21) on the saw table (7) and set to the desired

measurement.

• Turn the top saw band roller (2) a few times in a clockwise

direction.

• Check the setting of the top guide pins (38) again and ad-

just if necessary.

• If necessary, adjust the top support bearing (36) (8.4.1).

8.4.4 Adjusting the bottom guide pins (46)

(Fig.7+8)

• Disassemble saw table (7)

• Undo screw for bottom retainer (43) (Allen key, size 5)

• Move bottom retainer (47), bottom guide pins (46), until

the front edge of the bottom guide pins (46) is approx. 1

mm behind the tooth base of the saw band.

• Retighten screw for bottom retainer (43).

• ATTENTION! The saw band will be unusable if the teeth

touch the guide pins with the saw band running.

• Undo Allen screws for bottom guide pins (45).

• Slide the two bottom guide pins (46) sufﬁciently far in the

direction of the saw band that the distance between the

guide pins (46) and Bandsaw blade (21) is max. 0.5 mm.

(Saw band must not jam)

• Retighten Allen screws for bottom guide pins (45).

• Turn the bottom saw band roller (8) a few times in a clock-

wise direction.

• Check the setting of the bottom guide pins (46) again and

adjust if necessary.

• If necessary, adjust the bottom support bearing (42)

(8.4.2).

8.5 Adjusting the top saw band guide (5) (Fig. 9)

• Undo locking handle for saw band guide (23).

• Turn the adjustment handle for the saw band guide (22) to

lower the saw band guide (5) as closely as possible (dis-

tance approx. 2-3 mm) over the material to be cut.

• Retighten locking handle (23).

• Check the setting before every cutting process and adjust

if necessary.

8.6 Adjusting the saw table (7) to 90° (Fig. 10+11)

• Set the top saw blade guide (5) fully upwards.

• Undo locking handle (20) and wing nut (31) (Fig. 2).

• Place the angle bracket between the Bandsaw blade (21)

and saw table (7). Angle bracket not included in the scope

of supply.

• Tilt the saw table (7) by turning, until the angle to the

Bandsaw blade (21) is precisely 90°. If the saw table is

already on the screw (49) and a 90° angle cannot be set,

undo the nut (50) and shorten the screw (49) by turning in

a clockwise direction.

• Retighten the locking handle (20) and wing nut (31).

• Also undo the nut (50).

• Adjust the screw (49) sufﬁciently that the saw table touch-

es the underside.

• Retighten the nut (50) to ﬁx the screw (49) in position.

8.7 Which saw band to use

The saw band supplied in the band saw is intended for uni-

versal use. The following criteria should be considered when

selecting the saw band:

• It is possible to cut tighter radii with a narrow saw band

than with a wide saw band.

Hallo sehr geehrte Damen und Herren, ich suche einen Ersatz für die Bandsäge.
Einmal das Sägeblatt und zum anderen Die Bandauflage für die zwei Rollen.
Vielen Dank im Voraus. Submitted on 19-7-2022 at 10:02
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 303408 PBS 350 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 303408 PBS 350 A1 Manual

Product: