746858

Parkside IAN 292193 PDTS 6.3 A1 Manual

25
Zoom out
Zoom in
Previous page
1/117
Next page
GB/IE/NI 25
Safety instructions for pneumatic tools
Check that there is no damage or
wear on the spindle and spindle
thread.
Check that there can be no
hazards posed by sparks and
debris generated during use.
The pneumatic angle grinder
must be disconnected from its
power supply before maintenance
and before the parting disc is
replaced.
TRAPPING HAZARDS
There is a risk of strangulation, scalp-
ing, and/or other cutting injury when
loose clothing, jewellery, necklaces,
hair, or gloves are not kept away
from the machine and its accessories.
HAZARDS DURING
OPERATION
Avoid contact with the rotating
spindle and attached parting disc
to prevent cutting injuries to hands
and other parts of the body.
Using the machine may expose
the operating personnel’s hands
to hazards such as e.g. cuts,
scrapes, and heat. Wear suitable
gloves to protect the hands.
The operating and the mainte-
nance personnel must be
physically able to handle the
machine’s position, size, mass,
and power output.
Hold the machine correctly:
Be prepared to counteract the
usual or sudden movements –
keep both hands ready.
Make sure that your body is
balanced and that you are
standing on a stable surface.
Activate a startup or shutdown
control device in the event of
power outage.
Use only those lubricants recom-
mended by the manufacturer.
Goggles must be worn; gloves
and protective clothing are
recommended.
A hard hat must be worn for
overhead work.
Specify the runout time when
this is longer than 5 s; it is
recommended urgently
to place
the pneumatic angle grinder in a
protected place.
For abrasive cutting work, the
workpiece must be supported in
such a manner that the parting slit
maintains a constant or increasing
width during the whole work.
If the parting disc jams in a
parting slit, the pneumatic angle
grinder must be switched OFF and
the parting disc loosened. Before
resuming operation, check that
the parting disc has been secured
properly and is not damaged.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 292193 PDTS 6.3 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292193 PDTS 6.3 A1 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info