746594

Parkside IAN 284802 PNTS 250 A1 Manual

32
Zoom out
Zoom in
Previous page
1/128
Next page
GB IE
32
Unscrew the nut (right-hand
thread): turn counter-clockwise.
4. Remove the clamping ange (23)
and the dry grinding disc (5).
5. Fit on the new dry grinding disc
(5) with the intermediate card-
board layers (24) and the clamp-
ing ange (23), and screw the
grinding disc nut (22) manually
onto the nut (right-hand thread):
turn clockwise.
6. Tighten the grinding disc nut with
a screw wrench (AF19mm) ap-
plying modest manual force.
7. Screw the dry grinding disc cover
(4).
8. Adjust the spark protection holder
(
18) and the workpiece sup-
port (
6) - The distance from the
dry grinding wheel (5) must not
exceed 2 mm (see „Assembly“).
The grinding disc nut must not be
screwed too tightly in order to
avoid a breaking of the grinding
disc and nut.
9. Test run: Before starting work and af-
ter each change of grinding disc, carry
out a test run of at least 60 seconds
with no load. Switch off the equipment
immediately if the disc runs lumpy, sub-
stantial vibrations occur, or abnormal
noises are generated.
Change wet grinding disc:
1. Loosen the 3 xing screws
(13a/13b/13c) at the gear unit
housing (29) and remove the wa-
ter tank (13).
2. Unscrew the grinding disc nut (22)
with a screw wrench (AF19mm)
and hold against the wet grinding
disc (1) with one hand wearing a
glove.
Unscrew the nut (right-hand th-
read): turn counter-clockwise.
3. Remove the plastic clamping an-
ge (27) and the wet grinding disc
(1).
4. Fit on the new wet grinding disc
(1) and the plastic clamping an-
ge (27) and screw the grinding
disc nut (22) manually onto the
right-side nut (right-hand thread):
turn clockwise.
The two plastic clamping anges
(27/28) are not identical.
5. Tighten the grinding disc nut with
a screw wrench (AF19mm) ap-
plying modest manual force.
6. Push the water tank (13) back
over the wet grinding disc (1) and
onto the gear unit housing (29).
7. Fasten the water tank (13) back
on the gear unit housing (29)
using the three screws.
The grinding disc nut must not be
screwed too tightly in order to
avoid a breaking of the grinding
disc and nut.
8. Test run: Before starting work and af-
ter each change of grinding disc, carry
out a test run of at least 60 seconds
with no load. Switch off the equipment
immediately if the disc runs lumpy, sub-
stantial vibrations occur, or abnormal
noises are generated.
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 284802 PNTS 250 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 284802 PNTS 250 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info