745548

Parkside IAN 275685 PDKS 6.0 A1 Manual

10
Zoom out
Zoom in
Previous page
1/60
Next page
11 GB/IE
General safety rules / Before use / Start-up Start-up / After initial use / Cleaning and storage
After finishing the task, release the trigger
4
to
stop the saw from running.
After initial use
Once the task has been finished the device must be
disconnected from the compressed air connection.
This first requires the pressure to be completely re-
leased from the lines.
Briefly activate the trigger
4
on the device to
release any remaining compressed air.
Replacing the saw blade
Immediately replace the saw blade
1
if dull, wa
rped
or defective.
Always be sure the compressed air supply is dis-
connected when replacing the saw blade
1
!
First open the front cover
7
with a screwdriver
(see Fig. F).
Use the included socket head wrench
2
to
loosen the socket head screws on the saw blade
holder (see Fig. G) and remove the saw blade.
Then insert the new saw blade
1
into the saw
blade holder and tighten the socket head screws
again.
Ensure the saw blade
1
is correctly seated in
the saw blade holder and cannot be pulled out.
Then close the cover
7
with the screwdriver.
Adjusting/replacing the blade
guard
To adjust the blade guard
8
, loosen the two
outside screws (see Fig. H) with the included
2 mm hexagon socket wrench
3
. After loosen-
ing the screws you will be able to pull on the
blade guard to adjust it (see Fig. I).
You will now be able to adjust or replace the
blade guard.
After replacing or adjusting the blade guard,
tighten the previously loosened screws with the
hexagon socket wrench.
Cleaning and storage
To ensure a long life and trouble-free operation, it‘s
important to observe the following instructions.
Always disconnect the tool from the compressed
air supply before cleaning.
Clean your tool with a dry, soft cloth or lightly
blow it out with compressed air. Never use
caustic cleaners.
Lubricating the air saw
Note: Regular lubrication is required
to ensure the longest possible life to
air tools.
Turn the tool over so the air connection is facing
up and add a few drops of air tool oil or SAE
10–20 engine oil to the tool‘s air connection.
Activate the trigger
4
to allow the oil to dis-
perse better.
Hold a rag or absorbent paper towel in front
of the exhaust opening and run the tool on idle
for a few seconds.
ATTENTION! Remove the compressed
air connection before performing main-
tenance!
Excess oil will be blown out.
Keep persons or objects away from the discharge.
Storing the air saw
Store the air tool in a dry location, protected from
the weather and out of the reach of children.
Be sure moisture does not enter the inside of
the air tool.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 275685 PDKS 6.0 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275685 PDKS 6.0 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info