Manual Parkside IAN 275684 PDFP 500 B2 (page 7 of 50) (English, German, Dutch, Danish, French)

745540

Zoom out

Zoom in

1/50

PDFP 500 B2

Safety instructions for ﬁne spray

systems

■ Keep your work area clean, well lit and free

of paint and solvents, cloths and other inﬂam-

mable materials. Possible risk of spontaneous

combustion. Have a fully-functioning ﬁre extin-

guisher available at all times.

■ Ensure adequate ventilation in the spray zone

and suﬃcient fresh air in the entire room.

Evaporation of ﬂammable solvents will cause

an explosive environment.

■ Do not spray or clean with materials whose

ignition point is lower than 21°C. Use mater-

ials based on water, non-volatile hydrocarbons

or similar materials. The evaporation of volatile

solvents will cause an explosive environment.

■ Do not spray near ignition sources such as

static electric sparks, open ﬂames, ignition

ﬂames, hot items, motors, cigarettes and

sparks caused by plugging in/unplugging

power cables or by operating switches. These

ignition sources could cause a ﬁre to ignite in

the environment.

■ Do not spray any material if you do not know

whether it is potentially dangerous. Unknown

materials could cause dangerous conditions.

■ Wear additional personal protective equip-

ment such as suitable gloves and a protective

mask/respirator when spraying or handling

chemicals. Wearing appropriate protective

equipment for the conditions reduces your

exposure to dangerous substances.

■ Do not spray yourself, other people or animals.

Keep your hands and other body parts out

of the spray jet. If the spray jet pierces the

skin, seek medical assistance immediately. The

sprayed material can even penetrate through a

glove and into the skin and thus into your body.

■ Do not treat such a penetration injury like a

normal cut. A high-pressure jet can inject toxic

materials into the body and cause serious in-

juries. In the event of a chemical penetration of

the skin, seek medical assistance immediately.

■ Be aware of the potential hazards of the

sprayed material. Take note of the markings

on the container and the manufacturer's infor-

mation on the sprayed material, including the

instruction to use personal protective equip-

ment. The manufacturer's instructions are to

be followed to reduce the risk of ﬁre or injuries

caused by poisons, carcinogens, etc.

■ Never spray without the nozzle head ﬁtted.

Using a special nozzle with the appropriate

nozzle head reduces the likelihood of high-

pressure jets piercing the skin and injecting

poisons into your body.

Operation

HVLP properties

This appliance has a HVLP system (high volume,

low pressure). This ensures increased material

(paint) application and lower consumption.

IMPORTANT: Do not exceed the maximum working

pressure of 3 bar.

Connecting the device

■ The product may only be operated using

cleaned, condensate- and oil-free compressed

air and may not exceed the maximum operating

pressure of 3 bar on the appliance.

■ To ensure that you can regulate the air pressure,

the compressed air source should be equipped

with a (ﬁlter) pressure reducer.

You will need a ﬂexible compressed air hose

with a quick-disconnect coupling and a suitable

compressed air source to operate this appliance.

Follow all the operating and safety instructions for

the compressed air source and any special instruc-

tions regarding paint preparation.

NOTE

► Take note of the correct working pressure.

Excessively high pressure leads to strong

dispersion and overly-rapid liquid evapora-

tion. The surfaces become rough and develop

poor adhesion properties. If, however, the

working pressure is too low, the paint will not

be adequately dispersed. This leads to wavy

surfaces and droplets.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275684 PDFP 500 B2 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 275684 PDFP 500 B2 Manual

Product: