745468

Parkside IAN 275633 PABK 60 B2 Manual

10
Zoom out
Zoom in
Previous page
1/57
Next page
10 GB/IE
… / Cleaning and care / Information about warranty and service processingPreparations for use
Preparations for use
Warning: This appliance can slide on smooth sur-
faces during normal use. This can be prevented by
applying light pressure to the appliance.
Clean dusty surfaces so that the suction cups can grip
well. Otherwise a slight shift in position is possible.
Connecting the airbrush set
Be absolutely certain to disconnect the mains
plug before connecting the airbrush set to the
compressor and release the pressure in the lines
by actuating the vent of the air blow gun
9
.
Use the respective screw connection to connect
the spray stylus
3
with the coiled hose
2
and
the coiled hose to the airbrush connection
1
.
Use the included open-end wrench.
13
(see Ill. A).
Fasten the paint mixing beaker with connection
lid
5
to the spray stylus
3
(see Ill. B).
Insert the mains plug into the mains socket.
Note: For optimal results, professionals connect
an intermediate pressure reducer (not included
with delivery). The pressure reducer can be used
to adjust the compressed air at the spray gun
and optimise it to your needs.
Mixing paints for use
The paints included are water-soluble. In order to
properly apply the paints, add water and stir. As
delivered, the paints are too viscous.
First fill the beaker with your selected paint
colour with water.
Now screw the cover back on the beaker and
shake it.
Now remove two full droppers (1.5 mark on
the dropper) and fill these into a mixed glass
filled half way with water.
Shake the beaker. Now your paint has reached
the correct consistency.
Attach the paint mixing glass
5
according
to Ill. B.
Note: If desired, you can adjust the amount of
water added to influence the colour intensity
yourself as with a watercolour box. The more
water you add, the „thinner“ the colour.
You can also mix individualised colour tones
from the available colour pastes. Please take
note, there must be no paint clumps remaining
in the paint containers. The consistency should
correspond to that of water.
Note: If the paint used does not cover well, in-
crease the amount of paint in the mixture ratio.
Turning airbrush compressor
on / off
Turn the airbrush compressor
1
on by setting the
on / off switch
14
to the position “I“ (see Ill. C).
Turn the airbrush compressor
1
off by setting
the on / off switch
14
in the position “0“ (see
Ill. C).
Note: Full pressure is built up after two seconds.
Regulating the air pressure
Regulate the air pressure by actuating the vent
of the air blow gun
9
to more or less of an
extent.
The air pressure can be adjusted by turning the
air pressure regulator
15
.
The air gauge shows the pressure level.
Turning the air pressure regulator
15
to the left
reduces the air pressure, turning the air pres-
sure regulator
15
to the right increases the air
pressure.
An internal valve bleeds overpressure if it is not
reduced.
Regulating the spraying results
Regulate the amount of the paint supplied by
turning the paint nozzle of the spray stylus to
the right or left (see Ill. B).
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 275633 PABK 60 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275633 PABK 60 B2 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info