745534
11
Zoom out
Zoom in
Previous page
1/60
Next page
11
GB IE
5. Drill the hole until the depth stop
(2) comes in contact with the
component part.
Inserting/replacing the tool
1. Open the keyless chuck (4) wide
(RELEASE) so that the tool can
be inserted. To do so, rmly hold
the rear sleeve (4a) of the keyless
chuck (4) and turn the front sleeve
(4b) in the anti-clockwise direc-
tion.
2. Insert the tool as far as possible
into the keyless chuck (4).
3. Close the keyless chuck (4) (GRIP)
in order to clamp the tool. To do
so, rmly hold the rear sleeve
(4a) of the keyless chuck (4) and
turn the front sleeve (4b) in the
clockwise direction.
4. To remove the tool again, rotate
the keyless chuck (4) and pull out
the tool.
Always use a universal bit holder
use using a screwdriver bits.
Operation
Do not use the device with-
out the additional handle. It
provides additional hold and
reduces the risk of injury.
Observe noise control and local
regulations.
Switching on and off
1. Connect the machine to the pow-
er supply.
Make sure that the net voltage
matches the voltage rating indi-
cated on the device’s type plate.
2. Switching on: Press the on/off
switch (8).
3. By using the on/off switch (8)
you can progressively control the
speed.
Gentle pressure: low speed
Increase pressure: higher speed.
4. Continuous operation: Press the
lock button (9). The on/off switch
(8) is locked.
5. Switching off: Release the on/off
switch (8).
For continuous operation, briey
press the on/off switch (8).
Pre-select speed
You can pre-select the maximum speed on
the speed adjusting ring. The on/off switch
can only be pressed up to the specied
speed.
1. Wait for the device to shut-down.
2. Set the desired speed
on the speed adjusting
ring (7).
Set the direction of rotation
The device’s direction of rotation can be
changed with the rotational direction
switch.
1. Wait for the device to shut-down.
2. Push the rotational direction
speed (6) into the desired posi-
tion:
Clockwise rotation: to drill
and screw in screws.
Anticlockwise rotation: to
loosen screws.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 275325 PSBM 500 C4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275325 PSBM 500 C4 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info