745474
9
Zoom out
Zoom in
Previous page
1/29
Next page
9 GB/IE
If the tool is not in contact with the workpiece, the
fastener may be deflected away from your target.
Disconnect the tool from the power
source when the fastener jams in the
tool. While removing a jammed fastener, the
tacker may be accidentally activated if it is
plugged in.
Use caution while removing a jammed
fastener. The mechanism may be under com-
pression and the fastener may be forcefully
discharged while attempting to free a jammed
condition.
Do not use this tacker for fastening elec-
trical cables. It is not designed for electric ca-
ble installation and may damage the insulation
of electric cables thereby causing electric shock
or fire hazards.
Q
Safety advice relating specifi-
cally to Electric nailer / staplers
DANGER OF INJURY! Never point the de-
vice at yourself or at other people or animals.
Ensure that no people or animals are on the
other side of the workpiece.
PROTECT YOUR EYES! Wear eye protection
or goggles. This also applies to people who
may be helping with the work by supporting or
holding the workpiece.
Make sure the device is switched off before
you load the magazine. Set the ON / OFF
switch to position “0” and pull the mains plug
out of the mains socket!
Do not use the device to fix electrical cabling
in place.
Secure the workpiece. A workpiece held in a
clamp or vice is kept more securely in place
than one held by your hand.
Always work with the mains lead leading away
from the rear of the device.
DANGER OF INJURY! Use the device with
only the staples and nails specified above.
Ensure that the staples or nails do not project
from the surface of the workpiece or penetrate
through to the other side.
Short-term operation time: Let the device cool
down after 15 minutes of continuous operation.
DANGER OF INJURY! Keep your fingers and
other body parts away from the front plate
7
.
Never fire staples or nails through the air. At
short range the shot staples or nails could lead
to serious injury.
Only soft materials such as wood or textiles
should be joined using the device. Otherwise
the device could be damaged.
CAUTION! Connect the device to the mains
only when it is switched off. Set the ON / OFF
switch
3
to position “0”.
DANGER OF INJURY!
Switch the device on just before you intend to
use it. If you are not using the device, switch it
off to prevent unintentional firing.
Q
Before use
Q
Loading the magazine
Squeeze the end of the magazine slider
4
(see Fig. A).
Pull the magazine slider
4
out of the magazine
5
(see Fig. B).
Fill the magazine
5
with staples or nails
(see Fig. C).
Note on filling with nails: Use the right-
hand slot for filling with nails as shown in the
detailed image in Fig. C. Ensure that the nail
heads are all at the top.
NOTE: Observe the maximum capacity of ap-
prox. 85 staples or approx. 75 nails when filling.
After filling, push the magazine slider
4
into
the magazine
5
as far as it will go until you
hear and feel it engage.
NOTE: The magazine filling level indicator
6
allows you to see whether there are still staples
in the magazine.
Q
Setting the impact force
NOTE: Select the lowest impact force necessary
for your stapling.
Take into account the length of the staples or nails
to be used and the strength of the materials to be
joined.
Safety instructions for tackers / Before useGeneral power tool safety warnings / Safety instructions for tackers
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273474 PET 25 B1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273474 PET 25 B1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273474 PET 25 B1

Parkside IAN 273474 PET 25 B1 User Manual - French, Italian, Portuguese, Spanish - 61 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info