745342
9
Zoom out
Zoom in
Previous page
1/44
Next page
6
PFS 710 C2
GB
IE
Before use
Fitting/changing the saw blade
WARNING!
Always remove the plug from the power socket
before working on the appliance.
Otherwise, there is a risk of injury.
Turn the quick-release chuck
and hold it in
this position.
Press the required saw blade as far as it will go
into the quick-release chuck
.
Release the quick-release chuck
, it must
return to its initial position. The saw blade is
now locked.
Turning the handle
RISK OF INJURY!
Always remove the plug from the power socket
before working on the appliance. The handle
can be turned by 90° to the right or left.
This allows the ON / OFF switch to be
turned to a most suitable position depending
on the working condition.
Press the release button
and turn the handle
to the right or left.
Allow the handle
to engage.
Adjusting the footplate
RISK OF INJURY!
Always remove the plug from the power
socket before working on the appliance.
Adjust the footplate
according to the cutting
depth.
To do so, loosen the locking lever
and move
the footplate to the corresponding position.
Lock this position by tightening the locking lever
.
Stroke rate selection
Use the adjusting wheel to select the desired
stroke rate (– = lower stroke rate, + = increased
stroke rate).
The stroke rate can also be changed during opera-
tion.
Operation
Switching on and off
During operation, you can choose between instan-
taneous and continuous operation.
Switching to instantaneous operation:
Press the ON / OFF switch
. The working
light comes on with a slightly or fully pressed
ON /OFF switch and illuminates the work-
ing area in poor lighting conditions.
Switching off instantaneous operation:
Release the ON / OFF switch
.
Switching to continuous operation:
Press the ON / OFF switch
and lock it in this
position with the locking switch .
Switching off continuous operation:
Press the ON / OFF switch
and release it
again.
Guiding the sabre blade safely
To adapt to the workpiece and for safe placement,
the footplate can be swivelled. It must always
make contact with the workpiece when the appli-
ance is running.
Practical advice on sawing
Check the material to be worked to make sure
that all foreign objects have been removed, e.g.
nails, screws, etc..
Ensure that the ventilation slits are not covered.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 272950 PFS 710 C2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 272950 PFS 710 C2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info