Manual Parkside IAN 109910 PDFP 500 B2 (page 32 of 36) (French, Italian)

745455

Zoom out

Zoom in

1/36

32 GB

Initial use / Maintenance and CleaningSafety advice / Initial use

Wear additional personal protective

equipment such as appropriate protec-

tive gloves and protective masks or

respirators when spraying or handling

chemicals. The wearing of protective equipment

in such conditions reduces exposure to harmful

substances.

Do not spray on yourself, other people

or animals. Keep hands and other body

parts away from the spray jet. If the

spray penetrates the skin, seek medical help

immediately. The material being sprayed can

even penetrate the skin through a glove and be

injected into your body.

Do not treat an injection as a simple cut.

A high pressure jet may inject toxins

into the body and cause serious inju

ries.

If the spray is injected into the skin, seek medical

help immediately.

Pay attention to any possible dangers

of the material being sprayed. Note

the markings on the container or the

manufacturer’s information relating to

the material being sprayed, including

the instruction to use personal protec-

tive equipment. The manufacturer’s in-struc-

tions must be followed to reduce the risk of ﬁre, as

well as injuries caused by toxins, carcinogens, etc.

Never spray without the nozzle head

in place. The use of a special nozzle insert

with the appropriate nozzle head reduces the

probability of a high-pressure jet penetrating the

skin and injecting toxins into the body.

Initial use

HVLP properties

This device uses an HVLP system (High Volume Low

Pressure). It ensures the increased application of

(paint) materials with lower consumption.

Important: Do not exceed the maximum working

pressure of 3 bar.

Connecting the device

Operate the product only with cleaned, con-

densate- and oil-free compressed air and never

exceed the maximum working air pressure at

the device of 3 bar.

The compressed air source must be ﬁtted with a

(ﬁlter) / pressure reducer so that the air pressure

can be regulated.

In order to operate this device you require a ﬂexible

compressed air hose with quick-release coupling

and an appropriate source of compressed air.

Observe the operating and safety instructions of the

compressed air source and any special instructions

concerning paint preparation.

Note: Ensure the correct working pressure. An ex-

cessive working pressure leads to increased ﬁne

dispersion and results in too rapid evaporation of

the liquid. The surfaces become rough and develop

poor adhesion properties. If the working pressure is

too low on the other hand, the paint material is not

suﬃciently atomised. Undulating surfaces and the

formation of drops are the result.

Connect the compressed air hose with the

rapid-release coupling to the compressed air

connection

of the device. This automatically

locks into place.

Use the ﬁlter pressure reducer of the compressed

air source to set the working pressure to 3 bar.

Preparing the spraying surface

Mask oﬀ the surroundings of the spraying surface

thoroughly over a wide area. Otherwise all

non-covered areas or surfaces may become soiled.

Make sure that the spraying surface is clean,

dry

and free of grease.

Roughen smooth surfaces and then remove the

sanding dust.

Turning the device On / Oﬀ

Working Instructions:

- Insert the ﬁlter in the gun (see Fig. C).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 109910 PDFP 500 B2 in the language / languages: French, Italian as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 109910 PDFP 500 B2

Parkside IAN 109910 PDFP 500 B2 User Manual - English, German, Dutch, Danish, Swedish - 53 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 109910 PDFP 500 B2 Manual

Product: