Manual Parkside 360564 - IAN 360564 (page 14 of 140) (English, German, Dutch, Danish, French, Polish, Spanish)

763673

Zoom out

Zoom in

1/140

9GB/IE

9.2.1 Connection to an external dust extractor

• Attach the extraction hose of a workshop vacuum cleaner to

the extraction port (17a).

• The workshop vacuum cleaner must be suitable for the mate-

rial being worked.

Attention! Always observe the safety and warning notices of

the workshop vacuum cleaner being used.

• When vacuuming dust that is especially detrimental to health

or carcinogenic, use a special vacuum cleaner.

9.3 Precision adjustment of the stop for crosscut

90° (ﬁg. 1/6/7)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Loosen the set screw (22).

• Position the angle stop (A) between the saw blade (6) and

the rotary table (14).

• Loosen the lock nut (26a).

• Adjust the adjusting screw (26) until the angle between the

saw blade (6) and rotary table (14) is 90°.

• Re-tighten the lock nut (26a).

• Subsequently check the position of the angle indicator. If

necessary, loosen the pointer (19) using a Philips screwdriv-

er, set to position 0° on the angle scale (18) and re-tighten

the retaining screw.

9.4 Precision adjustment of the stop for mitre cut

45° (ﬁg. 1, 7-11)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Fix the rotary table (14) in the 0° position.

Attention! For mitre cuts (inclined saw head), the moveable

stop rail (16a) must be ﬁxed in the outer position (left side).

• Open the set screw (16b) for the moveable stop rails (16a)

and push the moveable stop rails (16a) outwards.

• The moveable stop rails (16a) must be locked so that the

distance between the stop rails (16a) and the saw blade (6)

is no more than 8 mm.

• The moveable stop rail (28) must be ﬁxed in the inner posi-

tion (right side).

• Before making the cut, check that no collision can occur be-

tween the stop rails (16a) and the saw blade (6).

• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) 45° to the left.

• 45° - position angle stop (B) between the saw blade (6) and

rotary table (14).

• Loosen the lock nut (27a) and adjust the adjustment screw

(27) until the angle between the saw blade (6) and the ro-

tary table (14) is precisely 45°.

• Re-tighten the lock nut (27a).

• Subsequently check the position of the angle indicator. If

necessary, loosen the pointer (19) using a Philips screwdriv-

er, set to position 45° on the angle scale (18) and re-tighten

the retaining screw.

10. Operation

10.1 Using the laser / LED (ﬁg. 12)

Function Press the ON/OFF switch

laser/LED (33)

1x.

OFF 1x

10.2 Changing the speed (ﬁg. 12)

The mitre saw has 2 speed ranges:

• To operate the mitre saw at a speed of 3200 rpm (metal), set

the speed regulation switch (34) to position I.

• To operate the saw at a speed of 5000 rpm (wood), set the

speed regulation switch (34) to position II.

10.3 Limiting the cutting depth (cutting grooves)

(ﬁg. 13)

m WARNING

Risk of kickback! When cutting grooves, it is

particularly important that no lateral pressure is

exerted on the saw blade. Otherwise, the saw

head might suddenly kick back! Use a clamping

device when cutting grooves. Avoid lateral pres-

sure on the saw head.

• The cutting depth can be inﬁnitely adjusted using the screw

(24). To do this, loosen the knurled nut (24a) on the screw

(24). Turn the screw (24) in or out to set the required cutting

depth. Then re-tighten the knurled nut (24a) on the screw

(24).

• Check the setting by completing a test cut.

10.4 Crosscut 90° and turntable 0° (ﬁg. 1/2/8)

In the case of cutting widths up to approx. 100 mm it is possible

to ﬁx the traction function of the saw with the set screw (20) in

the rear position. In this position the machine can be operated

in cross cutting mode. If the cutting width is over 100 mm then

it is necessary to ensure that the set screw (20) is loose and the

machine head (4) can move.

Attention! For 90° crosscuts, the moveable stop rail (16a)

must be ﬁxed in the inner position.

• Open the set screw (16b) for the moveable stop rails (16a)

and push the moveable stop rails (16a) inwards.

• The moveable stop rails (16a) must be locked so that the

distance between the stop rails (16a) and the saw blade (6)

is no more than 8 mm.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside 360564 - IAN 360564 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 4,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside 360564 - IAN 360564 Manual

Product: