568708
8
Zoom out
Zoom in
Previous page
1/52
Next page
EN-7
PLACEMENT Cont’d
ON A WALL
What’s included
1 x Wall-Mounting Bracket and 2 x Levelling Screws
Tools recommended (not included)
1 x Stud Finder
1 x Level
1 x Electric drill and appropriate drill bits
Hardware (not included)
5 x Screws appropriate to mounting surface
and weight of Soundscape.
5 x Wall anchors appropriate to mounting surface
and weight of Soundscape.
Paradigm does NOT supply
screws and anchor bolts to mount
Soundscape to a wall. Choose screws
and anchor bolts appropriate for size
and weight of Soundscape.
Dimensions of Soundscape (H x W x D):
5-1/2˝ x 42˝ x 5˝ / 14 cm x 106.7 x 12.7 cm.
Weight of Soundscape:
20 lb / 9.1 kg
We provide limited instructions for wall
mounting, please contact your Paradigm
Dealer for more detailed information.
The instructions that
follow assume the
mounting surface
is drywall with
standard wood studs. Should
you wish to mount to another
type of surface please consult
a certied contractor or your
Paradigm Dealer before you
begin the installation.
ACTION REQUIRED: When
mounting Soundcsape on a
wall for best results, adjust the
unit’s equalization and voicing
to make sure you are achieving
the best sound for the location.
Remove feet, if desired, before
wall mounting.
Use the Soundscapes internal
menu system to choose:
INSTAL > ON WALL.
Wall-Mounting Instructions
Follow the directions below and use the illustrations (Figs. 2 – 8)
provided on the following pages for guidance.
1 Decide on mounting location and use a level to make sure
Soundscape’s Wall-Mounting bracket sits level (Fig. 2).
2 Mark the three center pilot hole screw locations (Fig. 3).
3 Use a stud finder to determine if there is a stud behind
one of the three center screw locations (not shown).
If a stud is found drill a pilot hole. If no stud is found
use the centermost screw location and drill a pilot hole
for a wall anchor. Install wall anchor (not shown).
4 Using a screw, attach the bracket to the wall. DO NOT
tighten the screw at this point (Fig. 4).
5 Use a stud finder to determine if a stud lies behind any
of
the left and right screw locations. If a stud is found the
top and bottom screw holes with a stud behind them are
your screw locations. If no stud is found use the top
and bottom centermost screw locations as your screw
locations. Use a level to square the bracket and mark the
remaining pilot hole locations
(Fig. 5)
.
6 Remove the wall bracket or pivot bracket to allow access
to the remaining screw locations. a) If a stud is found,
drill pilot holes. b) If no stud is found drill pilot holes
and install wall anchors.
7 Using the screws, attach the wall bracket to the wall.
DO NOT fully tighten (Fig. 6).
8 Use a level to square the bracket, then tighten all screws
(Fig. 7).
9 Attach audio and power cables. Refer to ‘CONNECTION’
section of this manual for more information.
10 Move Soundscape into place. Drop the shoulder bolts
into the wall bracket keyholes (Fig. 8). Before releasing,
make sure the Soundscape has dropped fully into the
keyholes and is rmly in place (Fig. 8 Inset).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradigm Soundscape at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradigm Soundscape in the language / languages: English, French as an attachment in your email.

The manual is 5,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Paradigm Soundscape

Paradigm Soundscape Quick start guide - English - 2 pages

Paradigm Soundscape Quick start guide - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info