550986

Panasonic WV-SC384 Manual

86
Zoom out
Zoom in
Previous page
1/244
Next page
“8192kbps *” is available only when the image capture size is “1280x960” or “1280x720”.
“128kbps *” is available only when the image capture size is “QVGA”, “VGA”, “800x600”
*1
or “320x180”,
“640x360”.
“64kbps” is available only when the image capture size is “QVGA”, “VGA” or “320x180”, “640x360”.
“Unlimited*” is available only when “Frame rate” is selected for “Transmission priority”.
Note
• When “8192kbps *” or “Unlimited*” is selected, the number of users who can access H.264 images will
be limited to “1”. (Only a single user can access H.264 images.)
• The H.264 bit rate is limited by “Bandwidth control(bit rate)” on the [Network] tab of “Network” page
(®page 166). For this reason, the bit rate may be lower than the value when any value with an asterisk
(*) on the right is selected.
• It is impossible to select “Unlimited*” for both “H.264(1)” and “H.264(2)”.
[Image quality]
Select the image quality of H.264 images from the following.
Low(Motion priority)/ Normal/ Fine(Image quality priority)
• Default: Normal
Note
• When “Constant bit rate” or “Best effort” is selected for “Transmission priority”, this setting is available.
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images.
If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264
to diminish image distortions. However, the refresh interval may be longer than the set value.
0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s
• Default: 1s
[Transmission type]
Select the transmission type of H.264 images from the following.
• Unicast port (AUTO): Up to 14 users can access a single camera concurrently. “Unicast port1(Image)”
and “Unicast port2(Audio)” will automatically be selected when transmitting images and audio from the
camera. When it is unnecessary to fix the port number for H.264 image transmission such as when using
in a particular LAN environment, it is recommended to select “Unicast port (AUTO)”.
• Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select
“Unicast port1(Image)” and “Unicast port2(Audio)” manually to transmit images and audio from the camera.
It is possible to fix the port number of the router used for H.264 image transmission via the Internet by
setting “Unicast port (MANUAL)” (®page 166). Refer to the operating instructions of the router in use.
• Multicast: Unlimited number of users can access a single camera concurrently. Complete the entry field
of “Multicast address”, “Multicast port” and “Multicast TTL/HOPLimit” when transmitting H.264 images with
multicast.
* Refer to page 9 for further information about the maximum concurrent access number.
• Default: Unicast port (AUTO)
[Unicast port1(Image)]
*2
Enter the unicast port number (used to transmit images from the camera).
• Available port number: 1024 - 50000 (Only even numbers are available.)
• Default:
– H.264(1): 32004
– H.264(2): 32014
86 Operating Instructions
11 Configure the settings relating to images and audio [Image/Audio]
… 86 …


Need help? Post your question in this forum.

Forumrules
1

Forum

panasonic-wv-sc384

Reset search

  • What will happen when Viewnetcam service ends in March 2024? Submitted on 1-11-2023 at 06:38

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic WV-SC384 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic WV-SC384 in the language / languages: English as an attachment in your email.

The manual is 8,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic WV-SC384

Panasonic WV-SC384 User Manual - German - 248 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info