602927
9
Zoom out
Zoom in
Previous page
1/56
Next page
AUDIO
PC IN
TH-42PS9
1
678
3
9
45
10
15 14 13 12 11
2
9
Connections
Notes:
Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input
Terminal.
Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
The display resolution is a maximum of 640 × 480 dots (TH-42PS10BK/S), 768 × 768 dots (TH-42PH10BK/S),
1,024 × 768 dots (TH-50PH10BK/S, TH-58PH10BK) when the aspect mode is set to “4:3”, and 852 × 480 dots
(TH-42PS10BK/S), 1,024 × 768 dots (TH-42PH10BK/S), 1,366 × 768 dots (TH-50PH10BK/S, TH-58PH10BK) when
the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show
ne detail with suf cient clarity.
The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will
need to make setting changes to the computer at the time of connection.
Some PC models cannot be connected to the set.
There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
The computer shown in the illustration is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speci ed
frequency range.
Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component connection) or “RGB” (when RGB signal connection). (see page 38)
To use sync input VBS signals, use the connector which incorporates a 75-ohm termination resistance and which is
available on the market, for the connection of the HD connector where the VBS signals are to be input.
Signal Names for Mini D-sub 15P Connector
Pin Layout for PC Input
Terminal
PC Input Terminals connection
COMPUTER
Conversion adapter
(if necessary)
Mini D-sub 15p
RGB
PC cable
Stereo plug
Audio
Connect a cable which matches
the audio output terminal on the computer.
Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name
1
R (PR/CR)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (PB/CB)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
NC (not connected)
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TH42PS10BK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TH42PS10BK in the language / languages: English as an attachment in your email.

The manual is 9,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info