602612
29
Zoom out
Zoom in
Previous page
1/48
Next page
1/2
Signal
Bildschirmschoner
PC
Component/RGB in Wählen
RGB
Installation
OSD Sprache Deutsch
Signalquelle
Aus
Aus
Aus
Aus
Stand by modus
Power management
Auto power off
Power save modus
29
Energieeinsparung
Drücken zur Wahl von
“Power save modus”
“Stand by modus”
“Power management”
“Auto power off”.
Zur Wahl von “Ein” oder “Aus” drücken.
Ein Aus
Zum Beenden der Installation drücken.
Power save modus: Wenn diese Funktion aktiviert ist, wird der Helligkeitspegel des Plasmadisplays vermindert
und die Stromaufnahme verringert.
Stand by modus: Wenn diese Funktion aktiviert ist, wird die Stromaufnahme des Mikrocomputers während
der Betriebsbereitschaft (siehe Seite 12, 15, 16) und somit die Stromaufnahme des Gerätes
während der Betriebsbereitschaft verringert.
Power management: Wenn diese Funktion auf „Ein“ eingestellt ist, spricht sie unter den folgenden Bedingungen
an, um die Stromversorgung des Gerätes automatisch ein- oder auszuschalten.
Wenn bei Zuleitung eines PC-Eingangssignals ca. 30 Sekunden lang kein Bild (Sync-Signal)
erfasst wird:
Das Gerät wird ausgeschaltet (Bereitschaftszustand), und die Netzanzeige leuchtet
orangefarben auf.
Wenn ein Sync on G-Sync-Signal erfasst worden ist, wird das Gerät nicht ausgeschaltet.
Sobald danach wieder ein Bild (Sync-Signal) erfasst wird:
Das Gerät wird eingeschaltet, und die Netzanzeige leuchtet grün auf.
Wenn lediglich ein Sync on G-Sync-Signal erfasst worden ist, wird das Gerät nicht
eingeschaltet.
Hinweise:
Diese Funktion steht nur bei Zuleitung eines PC-Eingangssignals zur Verfügung.
Bei Zuleitung eines Signals vom PC-Eingang-Terminal-Board (TY-42TM6P) steht diese
Funktion nicht zur Verfügung.
Diese Funktion ist wirksam, wenn die Option „Sync“ auf „Auto“ eingestellt ist, die Option
„Component/RGB in Wählen” auf „RGB“ eingestellt ist sowie bei normaler Wiedergabe
(1-Bild-Anzeige).
Auto power off: Die Stromversorgung des Gerätes wird ausgeschaltet, wenn kein Signaleingang vorhanden ist.
Wenn diese Funktion aktiviert ist, wird das Gerät ausgeschaltet, wenn 10 Minuten lang kein
Signaleingang festgestellt wird.
Hinweise:
Diese Funktion steht nur bei Zuleitung eines PC-Eingangssignals zur Verfügung.
Diese Funktion ist wirksam, wenn die Option „Sync“ auf „Auto“ eingestellt ist, die Option
„Component/RGB in Wählen” auf „RGB“ eingestellt ist sowie bei normaler Wiedergabe
(1-Bild-Anzeige).
1
2
3
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TH42PH11ES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TH42PH11ES in the language / languages: German as an attachment in your email.

The manual is 7,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic TH42PH11ES

Panasonic TH42PH11ES User Manual - English - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info