602459
27
Zoom out
Zoom in
Previous page
1/76
Next page
27
Adjusting Pos. /Size
Auto Setup
When inputting a PC signal as an example, “H-Pos/V-Pos”, “H-Size/V-Size”, “Dot Clock” and
“Clock Phase” are automatically corrected.
This setting is enabled under the following conditions:
This setting is not activated during Digital Zoom.
When inputting an analog signal (Component/PC):
This setting is enabled if “Component/RGB-in select” (see page 40) in Setup menu is “RGB”.
When inputting a digital signal (HDMI/DVI):
A PC format signal enables this setting.
When the signal is not PC format, this setting is enabled only if “Over Scan” (see page 28) is
“Off” or “1:1 Pixel Mode” (see page 28) is “On”. “H-Size/V-Size” is not automatically adjusted.
This setting will be invalid and will not work under the following conditions:
When VIDEO signal input
Aspect is set to “Just”
“Display size” in the Options menu (see page 60) is set to “On”
Using Remote Control
When on the remote control is pressed, “Auto Setup” will be executed.
When Auto Setup does not work, “Invalid” is displayed.
Auto mode
When the “Auto Setup“ is set to “Auto” in the Options menu (see page 61), automatic position
adjustment starts:
When the display power is turned ON.
When the input signal is switched.
H-Pos
Adjust the horizontal position.
V-Pos
Adjust the vertical position.
H-Size
Adjust the horizontal size.
V-Size
Adjust the vertical size.
Dot Clock
(During Component/PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this
happens, adjust so that any such noise is minimized.
Clock Phase
(During Component/PC input signal)
Eliminate the ickering and distortion.
Notes:
If the dot clock frequency of an analog signal is 162 MHz or higher, “Dot Clock” and “Clock
Phase” cannot be automatically corrected.
When digital signal input, Dot Clock and Clock Phase cannot be made.
Auto Setup may not work when a cropped or dark image is input. In such case, switch to
a bright image with borders and other objects are clearly shown, and then try auto setup
again.
Depending on the signal, out of alignment may occur after Auto Setup. Carry out ne tuning
for the position/size as required.
If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz,
1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in “XGA Mode”
(see page 45) may results in correct Auto Setup.
Auto Setup does not work well when a signal such as additional information is superimposed
out of valid image period or intervals between synchronizing and image signals are short, or
for image signal with tri-level synchronizing signal added.
If Auto Setup cannot adjust correctly, select “Normalise” once and press OK button, then
adjust Pos. /Size manually.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TH42BT300ER at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TH42BT300ER in the language / languages: English as an attachment in your email.

The manual is 4,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic TH42BT300ER

Panasonic TH42BT300ER User Manual - English - 48 pages

Panasonic TH42BT300ER User Manual - English - 20 pages

Panasonic TH42BT300ER User Manual - German - 76 pages

Panasonic TH42BT300ER User Manual - German - 20 pages

Panasonic TH42BT300ER User Manual - Dutch - 76 pages

Panasonic TH42BT300ER User Manual - Dutch - 20 pages

Panasonic TH42BT300ER User Manual - Danish - 76 pages

Panasonic TH42BT300ER User Manual - French - 76 pages

Panasonic TH42BT300ER User Manual - French - 20 pages

Panasonic TH42BT300ER User Manual - Italian - 76 pages

Panasonic TH42BT300ER User Manual - Swedish - 76 pages

Panasonic TH42BT300ER User Manual - Swedish - 20 pages

Panasonic TH42BT300ER User Manual - Turkish - 77 pages

Panasonic TH42BT300ER User Manual - Spanish - 76 pages

Panasonic TH42BT300ER User Manual - Spanish - 20 pages

Panasonic TH42BT300ER User Manual - Norwegian - 20 pages

Panasonic TH42BT300ER User Manual - Finnish - 20 pages

Panasonic TH42BT300ER User Manual - All languages - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info