602343
17
Zoom out
Zoom in
Previous page
1/69
Next page
13
6789
13452
COMPUTER
RS-232C Straight cable
D-sub 9p
(Male)
(Female)
SERIAL Terminals connection
Notes:
Use the RS-232C straight cable to connect the computer to the Plasma Display.
The computer shown is for example purposes only.
Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface
speci cation, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the
sending and receiving of control data which satisfies
the conditions given below. Use a computer application
such as programming language software. Refer to the
documentation for the computer application for details.
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Pin layout for SERIAL Terminal
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command, the
parameters, and lastly an ETX signal in that order. If there
are no parameters, then the parameter signal does not
need to be sent.
STX C1 C2 C3 P1 P2 P3 P4: P5 ETX
Start
(02h)
3-character
command (3 bytes)
Colon Parameter(s)
(1 - 5 bytes)
End
(03h)
Notes:
If multiple commands are transmitted, be sure to wait for
the response for the rst command to come from this unit
before sending the next command.
If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
S1A and S1B of Command IMS are available only when
a dual input terminal board is attached.
Communication parameters
Signal level RS-232C compliant
Synchronization method Asynchronous
Baud rate 9600 bps
Parity None
Character length 8 bits
Stop bit 1 bit
Flow control -
Signal names for D-sub 9P connector
Pin No. Details
2
R X D
3
T X D
5
GND
4
6
Non use
7
8
(Shorted in this set)
1
9
NC
These signal names are those of computer speci cations.
Connections
Command
Command Parameter Control details
PON None Power ON
POF None Power OFF
AVL ** Volume 00 - 63
AMT
0 Audio MUTE OFF
1 Audio MUTE ON
IMS None
SL1
S1A
S1B
YP1
HM1
HM2
HM3
HM4
PC1
Input select (toggle)
SLOT input (SLOT INPUT)
SLOT input (SLOT INPUT A)
SLOT input (SLOT INPUT B)
COMPONENT/RGB IN input
(COMPONENT)
HDMI 1 input (HDMI1)
HDMI 2 input (HDMI2)
HDMI 3 input (HDMI3)
HDMI 4 input (HDMI4)
PC IN input (PC)
DAM None
ZOOM
FULL
JUST
NORM
ZOM2
ZOM3
SJST
SNOM
SFUL
14:9
Screen mode select (toggle)
Zoom1
(For Video/SD/PC signal)
16:9
Just (For Video/SD signal)
4:3 (For Video/SD/PC signal)
Zoom2 (For HD signal)
Zoom3 (For HD signal)
Just (For HD signal)
4:3 (For HD signal)
4:3 Full (For HD signal)
14:9
With the power off, this display responds to PON command
only.
Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to
“RS-232C”. (see page 52)
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TH103VX200W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TH103VX200W in the language / languages: English as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic TH103VX200W

Panasonic TH103VX200W User Manual - English - 44 pages

Panasonic TH103VX200W Quick start guide - English - 24 pages

Panasonic TH103VX200W User Manual - German - 44 pages

Panasonic TH103VX200W Quick start guide - German - 20 pages

Panasonic TH103VX200W Quick start guide - Dutch - 20 pages

Panasonic TH103VX200W User Manual - Dutch - 67 pages

Panasonic TH103VX200W Quick start guide - Danish - 20 pages

Panasonic TH103VX200W User Manual - Danish - 20 pages

Panasonic TH103VX200W Quick start guide - French - 24 pages

Panasonic TH103VX200W User Manual - French - 69 pages

Panasonic TH103VX200W Quick start guide - Italian - 20 pages

Panasonic TH103VX200W User Manual - Italian - 67 pages

Panasonic TH103VX200W Quick start guide - Swedish - 20 pages

Panasonic TH103VX200W User Manual - Swedish - 67 pages

Panasonic TH103VX200W User Manual - Turkish - 68 pages

Panasonic TH103VX200W User Manual - Spanish - 69 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info