•
Specifi cations
•
Frequently Asked Questions
TH-37PX71E TH-42PX71E TH-50PX71E
Power Source AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use 250 W 270 W 370 W
Standby condition
0.7 W (Without DVB recording)
20 W (With DVB recording)
0.5 W (Without DVB recording)
20 W (With DVB recording)
Display panel
Aspect Ratio 16:9
Visible screen size
94 cm (diagonal) 106 cm (diagonal) 127 cm (diagonal)
819 mm (W) × 457 mm (H) 922 mm (W) × 518 mm (H) 1,106 mm (W) × 622 mm (H)
Number of pixels
737,280 (1,024 (W) × 720 (H))
[3,072 × 720 dots]
786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
Sound
Speaker 160 mm × 42 mm × 2 pcs, 8
Ω
Audio Output 20 W (10 W + 10 W ), 10% THD
PC signals
VGA, SVGA, XGA
SXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems /
Band name
PAL B, G, H, I, SECAM B, G, SECAM L / L’
VHF E2 - E12 VHF H1 - H2 (ITALY)
VHF A - H (ITALY) UHF E21 - E69
CATV (S01 - S05) CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2 VHF R3 - R5
VHF R6 - R12 UHF E21 - E69
PAL 525/60 Playback of NTSC tape from some PAL Video re cord ers (VCR)
DVB Digital terrestrial services via VHF / UHF aerial input.
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only) Playback from NTSC Video recorders (VCR)
•
TV signals may not be received in some areas.
Aerial - Rear VHF / UHF
Operating Conditions
Temperature : 0 °C - 35 °C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
COMPONENT
VIDEO
Y 1.0 V[p-p] (including synchronization)
PB, PR ±0.35 V[p-p]
AUDIO L - R
RCA PIN Type × 2 0.5 V[rms]
Others
HDMI1 / 2 TYPE A Connectors
•
This TV supports “HDAVI Control 2” function.
PC
HIGH-DENSITY D-SUB 15PIN R,G,B/0.7 V[p-p] (75
Ω
)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
Output
AUDIO L - R
RCA PIN Type × 2 0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
917 mm × 667 mm × 330 mm
(With Pedestal)
917 mm × 620 mm × 97 mm
(TV only)
1,020 mm × 727 mm × 330 mm
(With Pedestal)
1,020 mm × 680 mm × 97 mm
(TV only)
1,210 mm × 841 mm × 369 mm
(With Pedestal)
1,210 mm × 793 mm × 97 mm
(TV only)
Mass
30.0 k
Net (With Pedestal)
23.0 k Net (TV only)
34.0 k Net (With Pedestal)
27.0 k Net (TV only)
45.0 k Net (With Pedestal)
38.0 k Net (TV only)
Problem Actions
Screen Sound HDMI
Chaotic image, noisy
•
Set “P-NR” in the Picture Menu (to remove noise). (p. 20)
•
Check nearby electrical products
(car, motorcycle, fl uorescent lamp).
No image can be
displayed
•
Is “Colour” or “Contrast” in the Picture Menu set to the minimum?
(p. 20)
•
Check Colour system. (p. 27)
Blurry or distorted image
(no sound or low volume)
•
Reset channels. (p. 27)
No sound is produced
•
Is “Sound mute” active? (p. 7)
•
Is the volume set to the minimum?
Sound level is low
or sound is distorted
•
Sound signal reception may be deteriorated.
•
Set “MPX” (p. 20) in the Sound Menu to “Mono”. (Analogue)
•
Check Sound system. (p. 27)
Sound is unusual
•
Set the sound setting of the connected equipment to
“2ch L.PCM”.
•
Check the “HDMI1 Input” setting in the Sound Menu. (p. 20)
•
If digital sound connection has a problem, select analogue sound
connection. (p. 33)
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
•
Is the HDMI cable connected properly? (p. 36)
•
Turn Off the TV and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 40)
•
Use an equipment compliant with EIA/CEA-861/861B.
Unusual image is displayed
•
Turn off the TV with Mains power On / Off switch, then turn it on
again.
TV goes into
“Standby mode”
•
Off Timer function is activated.
•
The TV enters “Standby mode” about 30 min.after broadcasting
ends.
The remote control
does not work
•
Are the batteries installed correctly? (p. 6)
•
Has the TV been switched On?
OtherDVB
•
Due to the digital reception technologies involved, quality of the DTV signals may be relatively low in
some cases, despite good reception of analogue programmes.
Interference or
frozen / disappearing
image in DVB
•
Check “DVB Signal Condition”. (p. 28)
If “Signal Quality” or “Signal Strength” are displayed in red,
check aerial.
If problem persists, consult your local Panasonic dealer.
•
Turn the TV off with the Mains power On / Off switch, then turn
it On again.
Unable to receive signals
with a high-performance aerial
•
Install an aerial individually for the TV and VCR
(or use a splitter).
TV
VCR
Aerial
Input
terminal
Aerial Output
Aerial Output
Aerial Input
(Individual aerial)
(Individual aerial)
Splitter
FAQs Specifi cations
Note
•
Design and Specifi cations are subject to change without notice. Weight and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
