33023
10
Zoom out
Zoom in
Previous page
1/193
Next page
10
Connection
Connect the IR Blaster if you wish to send remote control signals
from the plasma TV to control the recording of a connected
video recorder.
Position the IR Blaster remote control emitter facing the signal
sensor of the video recorder and you will be able to easily record
programs from digital broadcasts using a video recorder
connected to the plasma TV.
Setting the IR Blaster
IR Blaster Connection
Place the IR Blaster in front of the signal sensor of the video
recorder. (VCR)
Read the video recorder
operating instructions
regarding positioning of the
signal sensor.
If necessary, use the double sided adhesive tape (included)
to secure the IR Blaster to a flat surface.
e.g. Television stand surface
If you peel off the adhesive tape, the
surface may become damaged.
Once you have confirmed the video
recorder is operating correctly,
secure it by attaching the adhesive
tape.
DIGITAL
AUDIO OUT
G-LINK
IR Blaster (Supplied)
Infrared
emitter
Video recorder (VCR)
Video recorder
G-LINK jack
TV
TV
VCR DVD
DTV
RCVR
DBS/CBL
1 2 3
4 5 6
7 8
0
9
AUX
A
S
P
E
C
T
M
U
T
E
R
E
C
A
L
L
F
A
V
O
R
I
T
E
CH
VOL
CH
VOL
OK
+
-
Introduction to recording scheduling using the IR
Blaster
You may do recording scheduling from the TV Guide of this
TV after installing the IR Blaster. (See page 43)
The TV acts as a proxy for some remote control
operations of the VCR.
Setting the recording time,
channel and recording
mode, etc.
Converts scheduling data
displayed on the TV to a
remote control signal and
sends it
Settings other than basic ones (such as recording time
and channel) must be set on the VCR.
TV
No need to set
recording time or
channel on the
video recorder
VCR
INPUT / OUTPUT Connection
With the IR Blaster connection setting timer recording can be done easily by using the TV GUIDE function in this set.
AV IN
R L
AUDIO IN
S VIDEO
VIDEO
L
R
Y
VIDEO
AUDIO
P
B
P
R
P
B
P
R
Y
PROGOUTCOMPONENT VIDEO
INPUT
1
2
INPUT 2 INPUT 1
TO AUDIO AMP
AUDIO
IN
PC
AV IN
R L
AUDIO IN
S VIDEO
VIDEO
L
R
VIDEO
AUDIO
P
B
P
R
P
B
P
R
Y
PROGOUTCOMPONENT VIDEO
INPUT
1
2
INPUT 2 INPUT 1
TO AUDIO AMP
AUDIO
IN
PC
ANTENNA
Cable In
DIGITAL
AUDIO OUT
G-LINK
Connection for recording to a VCR by using TV GUIDE
Back of the TVG-LINK
from
PROG.OUT
To INPUT 1
IR Blaster
VCR
Notes:
The input signals connected to INPUT 1 cannot be output
from PROG. OUT terminals. (both Video and audio)
However, output can be obtained from optical Digital Audio
terminals.
(Input signals other than from INPUT 1 can be output
from PROG. OUT.)
When you make schedule recording using TV Guide with
IR blaster, you have to select in your VCR Line-1 (L-1)
and set your VCR in OFF condition.
(Refer to the Operating Instruction manual of VCR)
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TH-42PX500U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TH-42PX500U in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info