33057
56
Zoom out
Zoom in
Previous page
1/60
Next page
56
Troubleshooting
Before requesting service for this LCD/DVD combo, check the chart below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem,
consult your dealer for instructions.
For TV broadcasts (VHF, UHF)
Symptom
Power supply does not go on
Remote control cannot be
operated
Image shakes, or image is
unclear
There are spots on the picture,
or the screen shakes
The image appears doubled
or tripled
A color pattern appears, or
colors disappear
Only a certain channel looks bad
The channel number
disappears from the screen
When the image is not stable,
the screen turns completely
white for a moment
The screen goes dark
momentarily when the
channel is changed.
The TV makes a hissing
noise occasionally
The screen display shakes
with video input
There are parts at the top
and bottom of the screen
where there is no image
Top and bottom of picture
are missing after zoom
Cause and remedy
Is power supply plug unplugged from the outlet?
If power will not go on with the remote control, is the power supply of the TV "Off"?
Is battery exhausted, or is battery polarity wrong?
Is the remote control receiver illuminated with strong light from a fluorescent
lamp etc.?
Are you using the special-purpose remote control for this equipment? (The unit
will not operate with another remote control.)
Is there deterioration, breakage or disconnection of the antenna or antenna wire?
Is the antenna wire connected correctly?
Is the system affected (by radio wave interference or induced electromagnetic
waves) by external sources (automobiles or trains, high-voltage wires, neon,
motors, magnetized steel frame, or iron rain shutters, etc.)?
Turn off the power supply, and try changing the equipment setup location. If
that has no effect, separate magnet-proofing will be required.
Is the antenna direction shifted?
Are reflected electromagnetic waves being received from mountains or buildings?
Is the equipment being affected by another TV (electromagnetic interference)?
Changing the TV setup location may lead to improvement.
Is channel fine tuning correct?
Has the screen display button been pressed?
Press the "Screen display button" again.
If the system is switched to external input and there is no external signal
video, the number will disappear.
This occurs when the signal for driving the liquid crystal is lost, and is not a
malfunction.
The screen is darkened for a moment to conceal noise generated when changing
channels.
If the screen and audio are not abnormal, this sound is caused by slight expansion
and contraction of the cabinet due to changes in room temperature. It has no
effect on performance.
When input is switched to "video input", this may occur if there is no signal at the
video/audio input terminal.
With video software wider than 16:9 (cinema vision size software etc.) there are
parts at the top and bottom of the screen where there is no image.
Has the screen position adjustment been left shifted?
Adjust the screen position.
Page
13
7
8, 9
19
10, 18
21
24
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic TC11LV1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic TC11LV1 in the language / languages: English as an attachment in your email.

The manual is 1,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info