618696
33
Zoom out
Zoom in
Previous page
1/36
Next page
RQT8169
33
Troubleshooting guide
Progressive video
There is ghosting when
progressive output is on.
Picture not in progressive
output.
This problem is caused by the editing method or material used on DVD-Video, but should be 19
corrected if you use interlace output. Change “Video Output Mode” in Picture Menu to
“480i (or 525i)” or “576i (or 625i)”.
Press [SHIFT]+[PROGRESSIVE] so “PRG” is displayed. Or select “480p (or 525p)” or 13, 19
“576p (or 625p)” in “Video Output Mode” in Picture Menu.
If the unit is connected to the television through VIDEO OUT or S VIDEO OUT terminal, output 7
will be interlace, even if “PRG” is displayed.
Noise is heard.
ST flickers or doesnt light.
Sound is distorted.
A beat sound is heard.
A low hum is heard during AM
broadcasts.
Adjust the position of the FM or AM antenna.
Use an outdoor antenna. 30
Turn the television off or separate it from the unit.
Separate the antenna from other cables and cords.
Unit displays
Although the unit is on standby
mode, the display lights up and
changes continuously.
The display is dark.
NO PLAY
NO DISC
F61
DVD U11
ERROR
DVD HMM
MM stands for a number.
Turn off the demo function. 9
If you set the clock, demo function will be turned off automatically. 9
Press [SHIFT]+[DIMMER] to brighten the display. 29
You inserted a disc the unit cannot play; insert one that can. 4
You inserted a blank disc.
You haven’t inserted a disc; insert one.
You haven’t inserted the disc correctly; insert it correctly.
back cover
Check and correct the speaker cord connections. 6, 7
If this does not fix the problem, there is a power supply problem. Consult the dealer.
Disc is dirty. Wipe it clean. 4
Incorrect operation performed. Read the instructions and try again.
Trouble may have occurred. The number following “H” depends on the status of the unit.
Turn the unit off and back to ON. Alternatively, turn the unit off, disconnect the AC power
supply cord, and then reconnect it.
If the service numbers fail to clear, note the service number and contact a qualified service person.
Listening to the radio
You can only play DVD-Video if their region number is the same or includes the same region number
as the unit or if the DVD-Video is marked “ALL”. Confirm the region number for the unit on the back of
the main unit.
Select “On” in “On-Scr
een Messages” in “Display” tab. 21
The operation is prohibited by the unit or disc.
You are trying to display incompatible contents.
Television displays
This disc may not be played
in your region
No on-screen display.
Cannot display group xx,
content xx
Using the cassette deck
Picture abnormal or un-viewable Page
Some distortion is normal during SEARCH.
Ensure that the unit is connected directly to the television, and is not connected through a video 7
cassette recorder.
Change “TV Aspect” in the “Video” tab. 21
Change the Zoom setting. 15
The unit and television are using different video systems.
For Southeast Asia Use a multi-system or NTSC television.
For others Use a multi-system or PAL television.
The system used on the disc does not match your television.
PAL discs cannot be correctly viewed on an NTSC television.
This unit can convert NTSC signals to PAL 60 for viewing on a PAL television (“NTSC Disc 21
Output” in “Video” tab.)
Restore the zoom ratio to “x1.00”. 15
Set “Subtitle Position” in Display Menu to “0”. 19
Turn off TV’s zoom function.
Use the other preset aspect ratios or manual adjustment. 15
Zoom function may not work well, especially in dark scenes and may not work depending on
the type of disc.
Mobile telephone chargers can cause some disturbance.
If you are using a TV indoor antenna, change to an outdoor antenna.
The television antenna wire is too close to the unit. Separate the antenna wire of the television from the unit.
Clean the heads.
back cover
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. 23
Poor quality sound.
Recording is not possible.
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2.)
2 While pressing and holding down [
yy
yy
y/I] on the main unit, reconnect the AC power supply cord.
––––––––” appears on the display.
3 Release [
yy
yy
y/I].
All the settings are returned to the factory preset.
You will need to reset the memory items.
Picture distorted.
Picture size doesnt fit the
screen.
The television may display
incorrectly or colors appear
faded.
Menu is not displayed
correctly.
Auto zoom function does not
work well.
The picture on the television
disappears or stripes appear
on the screen.
RQT8169(32_33)new 4/18/05, 4:13 PM33
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCVK92D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCVK92D in the language / languages: English as an attachment in your email.

The manual is 4,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info