618123
25
Zoom out
Zoom in
Previous page
1/32
Next page
Operations
25
VQT3R83
Advanced
operations
Changing the dual audio
Change the dual audio from main to secondary.
1
Confirm the digital audio output setting on the
connected TV or player, etc. is set to “Bitstream”.
2 Press and hold [HDMI 1/2] for more than 2 sec.
3
While the indicator of the current setting is
flashing, press [HDMI 1/2] to change the setting.
The setting works only when the dual audio is
available in the audio source.
The setting is maintained until it is changed again.
The same setting is used for [TV] and [HDMI 1/2]
audio sources.
Remote control code
When other Panasonic devices respond to this
system’s remote control, change the remote control
code on the active subwoofer and the remote control.
Preparation
Turn off all other Panasonic products.
Turn on this system.
Change the remote control code to code 2:
1 Aim the remote control at this system’s remote
control sensor.
2 Press and hold [MUTE] and [HDMI 1/2] on the
remote control for more than 4 sec.
All the indicators will blink for 10 sec when the
code of this system is changed.
The setting is maintained until it is changed again.
If this system does not operate after changing the code,
repeat steps 1 and 2.
To change the remote control code to code 1, repeat the
steps above, but replace [HDMI 1/2] with [TV].
To turn off the 3D surround effect and
clear-mode dialog effect
Depending on your preference, it is possible to use
only the Dolby Virtual Speaker effect by turning off
the 3D surround effect and the clear-mode dialog
effect.
1 Press and hold [TV] for more than 2 sec.
The indicator for the current setting blinks for 10 sec.
2 While the indicator is blinking press [TV] to
change the setting.
The setting changes each time [TV] is pressed.
The setting will be reset to on when this system is turned off.
To turn off VIERA Link “HDAVI Control”
When “HDAVI Control” compatible equipment does
not work well with this system, for example, it is
possible to turn off this function as follows:
When VIERA Link is turned off the ARC function
is not available. Be sure to connect the optical
digital audio cable. (> 19)
1 Press and hold [MUTE] on the remote control
and [s VOL] on the active subwoofer for more
than 2 sec.
2
After the setting has changed, turn off all the
connected devices and then turn them on again.
To reduce the clear-mode dialog effect
When the dialog does not sound natural while the
volume is set low, for example, it is possible to
reduce the dialog enhancing effect as follows:
Press and hold [TV] on the remote control and
[s VOL] on the active subwoofer for more than
2 sec.
To turn off the volume limitation
If a state of the lowered volume disturbs you every
time this system turns on, for example, it is possible
to turn off this function as follows:
Press and hold [MUTE] on the remote control and
[VOL r] on the active subwoofer for more than
2 sec.
The settings of VIERA Link “HDAVI Control”, the clear-mode dialog
effect and the volume limitation remain intact even if you switch this
system to standby mode. To turn these 3 functions back on, this
system must be set back to the factory preset. (
>
26)
All the indicators will blink once when the setting is changed.
The following settings are unnecessary under
general usage conditions of the system.
A : Main
B : Secondary
A, B : Main and secondary
Only Dolby Virtual Speaker is on.
3D surround effect and clear-mode
dialog effect are also on.
SC-HTB15EGEBGNGS_VQT3R83.book Page 25 Tuesday, June 28, 2011 2:34 PM
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCHTB15EG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCHTB15EG in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SCHTB15EG

Panasonic SCHTB15EG User Manual - German - 144 pages

Panasonic SCHTB15EG User Manual - Dutch, Danish - 116 pages

Panasonic SCHTB15EG User Manual - French, Italian, Polish - 144 pages

Panasonic SCHTB15EG User Manual - Swedish, Spanish - 116 pages

Panasonic SCHTB15EG User Manual - Finnish - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info