18718
4
Zoom out
Zoom in
Previous page
1/36
Next page
4
RQT7696
Front speaker assembly
Simple setup
Front speaker assembly
Preparation
To prevent damage or scratches, lay down a soft cloth and
perform assembly on it.
For assembly, use a Phillips-head screwdriver.
1 Attach the pipe to the base.
1 Thread the speaker cable through the base.
2 Insert the pipe.
3
Secure the pipe to the base.
Ensure the screws are
securely fastened by lightly
tightening the left and right
side screws alternately until
fully tightened. (The heads
of the screws protrude
slightly even if you have fully
tightened them.)
2 Attach the stand to the speakers.
There is no difference between the right and left speakers and stands.
Using the polyfoam included with this unit may be convenient.
Ensure the stand is fastened on straight by lightly tightening the top
and bottom screws alternately until fully tightened.
Front speaker height
(Assembled diagram)
3 Adjust the speaker height.
Check the screws you tightened in procedures 1 and 2 if the pipe
and speaker are loose.
e.g. Attaching the stand to the lower rear
Make sure you have all the indicated components before starting assembly, setup, and
connection.
Front speaker units
Pipes
Bases
Large screws
Small screws
STEP1
The supplied stands are specially designed for
attachment to Panasonic SB-PF920 front speakers.
Only use as indicated in this setup.
Lessen excess
speaker cable.
Thread the
speaker cable
through here.
Cable
Groove
Holes for screws
Insert the pipe while gently
pulling on the speaker cable.
Rear side of base
Cable
Large
screws
Small screws
Front speaker
Polyfoam
Connection terminals
Mounting
plate
You can also attach to the upper rear of the speaker.
The height of the speaker is indicated in the diagram on the
right when attaching the stand to the upper rear or lower rear of
the speaker.
For your reference
You can enjoy good acoustics by
adjusting the height of the speaker to
the height of the television so the
center positions of both are
approximately the same.
1,138 mm
(44
13
/16z)
Speaker
Base
968 mm
(38
1
/8z)
796 mm
(31
11
/32z)
625 mm
(24
19
/32z)
678 mm
(26
11
/16z)
Stopper
screw
Do not
remove.
You can adjust within this range.
Attach to lower
rear of speaker
Attach to upper
rear of speaker
Pipe
Stopper screw
Screw to stop mounting plate from
moving or sliding below this point.
1 Loosen the attached speaker mounting
plate screw until the attached speaker is
slightly loose and adjustable.
2 With one hand on the base and the other
holding the speaker adjust the height of
the speaker up and down.
After adjusting the height tighten the screw
on the mounting plate securely.
Be careful not to loosen the screw
too much or the speaker may detach
and fall.
Phillips-head screwdriver
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCHT920 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCHT920 in the language / languages: English as an attachment in your email.

The manual is 2,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info