612777
8
Zoom out
Zoom in
Previous page
1/32
Next page
8
RQT0A22
9 Select “Connect” to apply the settings.
On the unit’s display, “SUCCESS” appears when the
connection is established. (The network indicator “
lights up.)
If “FAIL” is displayed press [OK], check the network
name (SSID) and the password, and then try the
setting again.
Depending on the device, the connection complete
screen may not be displayed.
10
Make sure to connect your compatible device back
to your home wireless network.
Enable Java and Cookies in your browser settings.
1 Press [RADIO/EXT-IN] on the remote control
repeatedly to select “NETWORK”.
2 To enter “WPS PUSH” mode
1 Press [SETUP] on the remote control repeatedly to
select “NET SETUP” and then press [OK].
“WPS PUSH” is indicated on the display.
2 Press [OK].
Alternatively, touch and hold [5/9] on the unit for
at least 4 seconds.
“WPS” flashes on the display.
3 Activate the WPS button on the wireless router.
On the unit’s display, “SUCCESS” appears when the
connection is established. (The network indicator “
lights up.)
"FAIL" may be displayed if the connection was not
made within the set time limit. Try the setting again. If
"FAIL" is still displayed, try other methods.
4 Press [OK] on the remote control to exit the
setting.
Using the WPS PIN code
1 Press [RADIO/EXT-IN] on the remote control
repeatedly to select “NETWORK”.
2 To enter “WPS PIN” mode
1 Press [SETUP] on the remote control repeatedly to
select “NET SETUP” and then press [OK].
2 Press [3, 4] on the remote control to select “WPS
PIN” and then press [OK].
Alternatively, touch and hold [:/6] on the unit for
at least 4 seconds.
The PIN code is indicated on the display.
3 Enter the PIN code into the wireless router.
Once the system enters WPS PIN code mode, you cannot
set up using the WPS button. To use the WPS button, turn
the system off and then on, and redo the network settings.
Depending on a router, other connected devices may
temporarily lose their connection.
For details, refer to the operating instructions of the wireless
router.
1 Disconnect the AC mains lead.
2 Connect the unit to a broadband router, etc. using
a LAN cable.
3 Connect the AC mains lead to the unit and turn
this system on.
When the connection is established, the network
indicator “ ” lights up.
Use category 5 or above straight LAN cables (STP) when
connecting to peripheral devices.
The LAN cable must be connected or disconnected while the
AC mains lead is disconnected.
Inserting any cable other than a LAN cable in the LAN port
can damage the system.
If the LAN cable is disconnected, the network-related
settings (l 9) will be initialized. In that case, make the
settings again.
When a LAN cable is connected, the Wi-Fi function will be
disabled.
Method 2:
Using WPS (Wi-Fi Protected Setup
TM
)
A compatible wireless router may have the WPS
identifier mark.
●●●●●●●●
e.g.,
Wired LAN connection
Method 3:
Using a LAN cable
ロモワ
ドヒパャモヴユノヵバ
ヒパパャモヴユノヵヹナ
LAN cable
(not supplied)
Broadband router, etc.
e.g.,
SC-ALL5CD-EGEBGN~RQT0A22.book 8 ページ 2015年4月23日 木曜日 午後4時44分
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCALL5CDGN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCALL5CDGN in the language / languages: English as an attachment in your email.

The manual is 5,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SCALL5CDGN

Panasonic SCALL5CDGN Quick start guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info