734669
12
Zoom out
Zoom in
Previous page
1/16
Next page
TQBM0358
12
Others
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being used
for approximately 20 minutes.
To cancel this function
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [2, 1] to select “OFF” and then press
[OK].
Note:
To turn the function on, select “ON” in step 2.
This setting cannot be selected when radio is the source.
When connected to a Bluetooth
®
device, the function does
not work.
Occasionally, Panasonic may release updated software
for this unit that may add or improve the way a feature
operates. These updates are available free of charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
The version of the installed software is displayed.
Press [OK] to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult
your dealer for instructions.
Cannot turn on the unit.
After connecting the AC mains lead, wait about
10 seconds before turning on the unit.
No operations can be done with the remote control.
Examine that the battery is installed correctly.
Sound is distorted or no sound.
Adjust the volume of the system.
Switch off the system, determine and correct the cause,
then switch the system on again. It can be caused by
straining of the speakers through excessive volume or
power, and when using the system in a hot environment.
Ensure the speaker cables are connected correctly
and securely. (> 4)
The digital audio input terminal of this unit can only
detect linear PCM (LPCM) signals. For details, refer to
the operating instructions of the device.
A “humming” sound can be heard during playback.
An AC mains lead or fluorescent light is near the
cables. Keep other appliances and cords away from
the cables of this system.
The unit does not work.
One of the unit’s safety devices may have been activated.
1 Press [Í/I] on the unit to switch the unit to standby.
If the unit does not turn off, disconnect the AC mains
lead from the AC outlet, reconnect it to the outlet after
about 30 seconds. Then wait for about 10 seconds.
2 Press [Í/I] on the unit to switch it on. If the unit still
cannot be operated, consult the dealer.
Noise is heard.
During “AUX” mode, when a device is connected to
both the AUX IN terminals and the USB port, noise
may be generated depending on the device. In this
case, remove the USB cable from the USB port.
Display not shown correctly.
Playback does not start.
You have not put in the disc correctly. Put it in correctly.
Disc is dirty. Clean the disc.
Replace the disc if it is scratched, warped, or non-standard.
There is condensation. Let the system dry for 1 to 2 hours.
Reception is poor or a beat sound is heard.
Keep the antenna away from computers, TVs, other
cables and cords.
Use an outdoor antenna.
Switch off the TV or move it away from the system.
If noise is excessive during FM reception.
Change the audio to be output as monaural.
1 Press [RADIO MENU] repeatedly to select “FM MODE”.
2 Press [2, 1] to select “MONO” and then press [OK].
The sound becomes monaural.
To cancel, select “STEREO” or change the frequency.
In normal circumstances, select “STEREO”.
The USB device or the contents in it cannot be read.
The format of the USB device or the contents in it is/
are not compatible with the system.
Slow operation of the USB device.
Large content size or large memory USB device takes
longer time to read.
The elapsed time shown is different from the actual
play time.
Transfer the data to another USB device or backup the
data and reformat the USB device.
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device cannot be connected.
The pairing of the device was unsuccessful or the
registration has been replaced. Try pairing the device
again.
This system might be connected to a different device.
Disconnect the other device and try pairing the device
again.
If “MODE 2” is selected in “LINK MODE”, select
“MODE 1”. (> 6)
If the problem persists, turn the unit off and on, then try
again.
The device is connected but audio cannot be heard
through this system.
For some built-in Bluetooth
®
devices, you have to set
the audio output to “SC-PMX92” or “SC-PMX90”
manually. Read the operating instructions for the
device for details.
The sound is interrupted.
The device is out of the 10 m communication range.
Bring the Bluetooth
®
device closer to this system.
Remove any obstacle between this system and the
device.
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.)
are interfering. Bring the Bluetooth
®
device closer to
this system and distance it from the other devices.
Select “MODE 1” for stable communication. (> 6)
Auto off function
Software update
Checking the software version
Common problems
Disc
Radio
USB
Bluetooth
®
SC-PMX90-92-EGEBGN~TQBM0358.book 12 ページ 2019年1月16日 水曜日 午後2時55分
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-PMX90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-PMX90 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-PMX90

Panasonic SC-PMX90 User Manual - German, Dutch, French, Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info