563930
15
Zoom out
Zoom in
Previous page
1/20
Next page
15
VQT4Z19
Others
1
Press [SETUP] to select “Dimmer”.
2 Press [2, 1] to select “On” and then press [OK].
Note:
To cancel, select “Off” in step 2.
This function switches off the system (except in radio
source) if you do not use the system for approximately
20 minutes.
1 Press [SETUP] repeatedly to select “Auto Off”.
2 Press [2, 1] to select “On” and then press [OK].
Note:
To cancel, select “Off” in step 2.
When connected to a Bluetooth
®
device, this function does
not work.
If “Net Standby” is set to “On”, this function will also be set
to “On”. To change the setting, set “Net Standby” to “Off”.
(> right)
Occasionally, Panasonic may release updated software
for this system that may add or improve the way a
feature operates. These updates are available free of
charge.
Preparation
Turn this system on.
Connect this system to the home network. (> 6)
Make sure that the network is connected to the
Internet.
If “D.Connect” is set to “On”, change the setting to
“Off” and connect this system to a network that is
connected to the Internet.
1 Press [SETUP] repeatedly to select “SW Update”
and then press [OK].
2 Press [2, 1] to select “Update? Yes” and then
press [OK] to start the update.
Select “Update? No” to cancel the update.
{. After the update has finished, “Success” is displayed.
3 Disconnect the AC mains lead and reconnect it
after 3 minutes.
If there are no updates, “No Need” is displayed.
Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
Checking the software version
1 Press [SETUP] repeatedly to select “SW Version” and
then press [OK].
{. The version of the installed software is displayed.
2 Press [OK] to exit.
To check the Wi-Fi signal strength where this system is
located.
Preparation
Connect this system to the wireless network. (> 6)
1 Press [SETUP] repeatedly to select “Signal
Level” and then press [OK].
This system’s displays show “Level ”.
(“ ” stands for a number.)
2 Press [OK] to exit this display mode.
It is recommended to have a signal strength of “3”. Change
the position or angle of your wireless network router or this
system if the indication is “2” or “1” and see if the
connection improves.
If “Level 0” is displayed, this system cannot establish a link
with the wireless network router. (> 17)
This function does not work when “D.Connect” is set to
“On”.
The wireless LAN function can be enabled or disabled.
1 Press [SETUP] repeatedly to select
“Wireless LAN” and then press [OK].
2 Press [2, 1] to select “On” or “Off” and then
press [OK].
The factory preset is “On”.
This system can turn on automatically from standby mode
when this system is selected as the AirPlay speakers.
Preparation
Connect this system to the home network. (> 6)
1 Press [SETUP] repeatedly to select
“Net Standby” and then press [OK].
2 Press [2, 1] to select “On” and then press [OK].
To cancel this function, select “Off” in step 2.
The factory preset is “Off”. If this function is set to “On” the
standby power consumption will increase.
Display the name for the connected wireless network
(SSID).
1 Press [SETUP] repeatedly to select “Net Info”
and then press [OK].
“IP Addr.” is indicated on the display.
2 Press [SETUP] repeatedly to select “SSID” and
then press [OK].
3 Press [OK] to exit.
If “No Connect” is displayed this system is not connected to
a wireless network.
All letters are displayed as capital letters, and characters
that cannot be displayed are replaced with “
¢”.
To check this system’s IP address or the Wi-Fi MAC address.
1 Press [SETUP] repeatedly to select “Net Info”
and then press [OK].
“IP Addr.” is indicated on the display.
2 Press [SETUP] repeatedly to select “IP Addr.” or
“MAC Addr.”and then press [OK].
The IP address or the MAC address is partially
displayed.
3 Press [2, 1] on the remote control to show the
rest of the IP address or the MAC address.
To exit the setting, wait 20 sec.
The “ – ” displayed on the top or bottom left of the display
indicate the first and last units respectively.
Decrease the brightness of the display panel
Automatically switch off the system
Software update
DO NOT DISCONNECT the AC mains lead while
one of the following messages is displayed.
“Linking”, “Updating” or “%”
(“ ” stands for a number.)
During the update process, no other operations can be
performed.
Wi-Fi signal strength
Wireless LAN setting
Network standby
Wireless network name (SSID)
IP/MAC Address
SC-PMX9-VQT4Z19.book 15 ページ 2013年3月21日 木曜日 午後4時16分
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-PMX9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-PMX9 in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-PMX9

Panasonic SC-PMX9 User Manual - English - 76 pages

Panasonic SC-PMX9 Quick start guide - English - 1 pages

Panasonic SC-PMX9 User Manual - English - 3 pages

Panasonic SC-PMX9 User Manual - German - 128 pages

Panasonic SC-PMX9 Quick start guide - German - 4 pages

Panasonic SC-PMX9 User Manual - Dutch - 128 pages

Panasonic SC-PMX9 Quick start guide - Dutch - 4 pages

Panasonic SC-PMX9 User Manual - Danish - 128 pages

Panasonic SC-PMX9 Quick start guide - Danish - 4 pages

Panasonic SC-PMX9 User Manual - French - 128 pages

Panasonic SC-PMX9 Quick start guide - French - 4 pages

Panasonic SC-PMX9 User Manual - Italian - 128 pages

Panasonic SC-PMX9 Quick start guide - Italian - 4 pages

Panasonic SC-PMX9 User Manual - Polish - 76 pages

Panasonic SC-PMX9 User Manual - Polish - 3 pages

Panasonic SC-PMX9 User Manual - Swedish - 128 pages

Panasonic SC-PMX9 Quick start guide - Swedish - 4 pages

Panasonic SC-PMX9 User Manual - Spanish - 128 pages

Panasonic SC-PMX9 Quick start guide - Spanish - 4 pages

Panasonic SC-PMX9 User Manual - Finnish - 76 pages

Panasonic SC-PMX9 Quick start guide - Finnish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info