618356
9
Zoom out
Zoom in
Previous page
1/40
Next page
9
VQT4U48
ENGLISH
Troubleshooting
Before requesting service, make the following checks.
If you are in doubt about some of the check points, or if
the solutions indicated in the following guide do not
solve the problem, consult your dealer for instructions.
Humming heard during play.
An AC mains lead or fluorescent light is near the cords. Keep
other appliances and cords away from this unit’s cables.
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device cannot be connected.
The pairing of the device was unsuccessful or the registration has
been replaced. Try pairing the device again.
This unit might be connected to a different device. Disconnect the
other device and try pairing the device again.
The device is connected but audio cannot be heard
through this unit.
For some built-in Bluetooth
®
devices, you have to set the audio
output to “SC-NE1” manually. Read the operating instructions for
the device for details.
The sound is interrupted.
The device is out of the 10 m communication range. Bring the
Bluetooth
®
device closer to this unit.
Remove any obstacle between this unit and the device.
Other devices that use the 2.4 GHz frequency band (wireless
router, microwaves, cordless phones, etc.) are interfering. Bring
the Bluetooth
®
device closer to this unit and distance it from the
other devices.
Select “MODE 1” for stable communication. (l 6)
The remote control doesn’t work properly.
The remote control and this unit are using a different code.
(l below, “REMOTE ”)
Is the battery depleted or is the battery inserted incorrectly? (l 4)
The following messages or service numbers may
appear on the unit’s display.
“AUTO OFF”
The unit has been left unused for about 30 minutes and will shut
down within a minute. Press any button to cancel it.
“ERROR”
Incorrect operation is performed. Read the instructions and try
again.
“F ” (“ ” stands for a number.)
There is a problem with this unit.
Note down the displayed number, disconnect the AC mains lead
and consult your dealer.
“REMOTE ” (“ ” stands for a number.)
The remote control and this unit are using different codes. Change
the code on the remote control.
When “REMOTE 1” is displayed, press and hold [OK] and
[ , AUX] for more than 4 seconds.
When “REMOTE 2” is displayed, press and hold [OK] and
[SOUND] for more than 4 seconds.
To return all settings to the factory preset
When the following situations occur, reset the
memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
1 Disconnect the AC mains lead. (Wait for at least
3 minutes before proceeding to step 2.)
2 While pressing and holding down [Í/I] on the
unit, reconnect the AC mains lead.
Keep holding down [Í/I] until “--------” appears
on the display.
3 Release [Í/I].
All the settings are returned to the factory preset. You will
need to reset the memory items.
Common problems
Bluetooth
®
Remote control
Messages
SC-NE1_EG~VQT4U48.book 9 ページ 2013年1月15日 火曜日 午後1時4
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-NE1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-NE1 in the language / languages: English, Polish as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-NE1

Panasonic SC-NE1 User Manual - German, Dutch - 52 pages

Panasonic SC-NE1 User Manual - Danish - 52 pages

Panasonic SC-NE1 User Manual - French, Italian - 52 pages

Panasonic SC-NE1 User Manual - Swedish, Spanish, Finnish - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info