696387
23
Zoom out
Zoom in
Previous page
1/40
Next page
Operations
23
TQBM0479
Setup menu
1 Press [SETUP] repeatedly to select
the setup item and then press [OK].
You can also press [4] or [3] repeatedly to select the
setup item.
2Press [4][3] repeatedly to select the
desired setting and then press [OK].
DIMMER
Switch the brightness of the display.
While “DISPLAY OFF” is set, the display lights for about
5 seconds if operations are performed on the main unit or
with the remote control.
While “DISPLAY OFF” is set, a part of the display lights if
the display is off but the main unit is on.
BEEP
A beep sounds when you touch the switch on the
main unit or when you turn the unit on/off.
This works during muting as well.
AUTO OFF
The main unit automatically is turned off if there is
no audio input and when you do not use it for
approx. 20 minutes.
When this is set, the display shows “P.OFF 1MIN” to
indicate that the main unit will turn off in approximately 1
minute.
If “STANDBY MODE” or “VIERA LINK” is set to “ON”, this
function will also be set to “ON”. To change the setting, set
“STANDBY MODE” and “VIERA LINK” to “OFF”. (> 23)
VOL LIMITATION
When this function is set to “ON”, if the volume
exceeds 50 when the main unit is turned off, then
the volume is set to 50 when the main unit is
turned on.
LINK MODE
Change the Bluetooth
®
transmission mode to
prioritise transmission quality or sound quality.
Make sure that the Bluetooth
®
device is not
connected (“BLUETOOTH READY” is indicated
on the display).
MODE 1: Emphasis on connectivity.
MODE 2: Emphasis on sound quality.
The default setting is “MODE 2”.
VIERA LINK
Turn on the VIERA Link function.
Select “OFF” when your HDAVI Control device
does not work correctly with this system.
ARC will be disabled. Connect an optical digital audio
cable.
Turn off all connected devices and then turn them on again
after changing the setting.
STANDBY MODE
When this function is set to “ON”, then the main
unit automatically turns on in the following cases.
When a Bluetooth
®
connection is established to the main
unit from a paired Bluetooth
®
device.
When playback operations are performed on the main unit
from a device connected to the network.
The default setting is “ON”.
If this function is set to “ON”, the standby power
consumption will increase. (> 32)
Wi-Fi
The wireless LAN function can be enabled or
disabled.
Wi-Fi SIGNAL LEVEL
You can check the signal strength of the wireless
connection.
The signal strength is displayed when you press [OK] while
“Wi-Fi SIGNAL LEVEL” is being displayed.
Press [OK] again to stop the display.
It is recommended to have a signal strength of “LEVEL 3”.
Change the position or angle of your wireless network
router or this system if the indication is “LEVEL 2” or
“LEVEL 1” and see if the connection improves.
If “LEVEL 0” is displayed, this system cannot establish a
link with the wireless network router.
“WIRED LAN” is displayed when connected with a LAN
cable.
NET INFO
You can confirm the IP address allocated to this
system, the MAC address of this system, and the
network name (SSID) of this system.
IP ADDRESS
SSID
MAC ADDRESS
Characters that cannot be displayed are replaced with
”.
RESET
This restores the settings to the factory presets.
For details, refer to “To return to the factory preset.” (> 26)
SC-HTB900-EGEBGN-TQBM0479_eng.book 23 ページ 2019年10月15日 火曜日 午後3時12分
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HTB900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HTB900 in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-HTB900

Panasonic SC-HTB900 User Manual - German, Dutch, French, Italian, Spanish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info