618145
33
Zoom out
Zoom in
Previous page
1/44
Next page
Operations
RQT9849
33
Depending on your preference, It is possible to
turn off the 3D surround effect and the clear-
mode dialog effect.
While pressing and holding
[SOUND] on the remote control,
press and hold [VOL r] on the main
unit for more than 4 sec.
While the setting is displayed, press
[SOUND] to change the setting.
The setting changes each time [SOUND] is pressed.
The indicator for the selected setting blinks for 20 sec and
then exits the setting mode.
This setting will be reset to on when the main unit is turned
off.
When off is selected, the dialog effect level cannot be
adjusted.
You can turn off dimmer mode and keep the LED
indicators bright.
While pressing and holding [INPUT
SELECTOR] on the remote control,
press and hold [s VOL] on the main unit
for more than 4 sec to turn off Dimmer
mode.
The indicator for the current condition will turn brighter.
The setting is maintained until it is changed again.
Default setting of this function is on.
To turn on dimmer mode, repeat the operation above.
After performing the operation, the indicator for the current
condition will be dim.
With this function turned on, this unit can be set to
automatically switch to standby mode if there is no
signal input and no operation is performed for 2 hours.
While pressing and holding
[DIALOG LEVEL j] on the remote
control, press and hold [INPUT
SELECTOR] on the main unit for
more than 4 sec.
The indicator for the current setting blinks for 20 sec.
While the indicator is blinking,
press [DIALOG LEVEL j] to change
the setting.
The setting changes each time [DIALOG LEVEL j] is
pressed.
The setting is maintained until it is changed again.
Remote control code
When other Panasonic devices respond to this
system’s remote control, change the remote control
code on this system and the remote control.
Preparation
Turn off all other Panasonic products.
Turn on the main unit.
Change the remote control code to code 2:
1 Aim the remote control at the main unit’s
remote control sensor.
2 Press and hold [MUTE] and [ ] on the
remote control for more than 4 sec.
All the indicators will blink for 10 sec when the
code of this system is changed.
The setting is maintained until it is changed again.
If the main unit does not operate after changing the code,
repeat steps 1 and 2.
To change the remote control code to code 1, repeat the
steps above, but replace [ ] with [INPUT SELECTOR].
Using the Dolby Virtual
Speaker effect
“STANDARD” indicator blinks:
3D surround effect and clear-mode
dialog effect is on.
“STEREO” indicator blinks:
3D surround effect and clear-mode
dialog effect is off.
Dimmer mode
Auto standby function
“STANDARD” indicator blinks:
Auto standby function is on.
“STEREO” indicator blinks:
Auto standby function is off.
Others
SC-HTB770_RQT9849-B_mst.book 33 ページ 2013年2月25日 月曜日 午前11時53分
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HTB770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HTB770 in the language / languages: English as an attachment in your email.

The manual is 12,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-HTB770

Panasonic SC-HTB770 Quick start guide - English - 2 pages

Panasonic SC-HTB770 User Manual - German - 124 pages

Panasonic SC-HTB770 User Manual - German - 44 pages

Panasonic SC-HTB770 User Manual - Dutch - 124 pages

Panasonic SC-HTB770 User Manual - Dutch - 44 pages

Panasonic SC-HTB770 User Manual - Danish - 124 pages

Panasonic SC-HTB770 User Manual - Danish - 44 pages

Panasonic SC-HTB770 User Manual - French - 44 pages

Panasonic SC-HTB770 User Manual - French - 44 pages

Panasonic SC-HTB770 User Manual - Italian - 124 pages

Panasonic SC-HTB770 User Manual - Italian - 44 pages

Panasonic SC-HTB770 User Manual - Polish - 124 pages

Panasonic SC-HTB770 User Manual - Polish - 44 pages

Panasonic SC-HTB770 User Manual - Swedish - 124 pages

Panasonic SC-HTB770 User Manual - Swedish, Spanish - 44 pages

Panasonic SC-HTB770 User Manual - Finnish - 124 pages

Panasonic SC-HTB770 User Manual - Finnish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info