734493
21
Zoom out
Zoom in
Previous page
1/32
Next page
21
TQBJ2216
Troubleshooting
Before requesting service, make the following
checks. If you are in doubt about some of the
check points, or if the solutions indicated do not
solve the problem, consult your dealer for
instructions.
Common problems
No power
After connecting the AC mains lead, wait about
10 seconds before switching on the main unit.
Disconnect the AC mains lead for 10 seconds
before connect again.
After switching on the main unit, if the main unit
immediately switches off, disconnect the AC mains
lead and consult your dealer.
If the main unit does not switch on when switching
on TV (HDMI CEC), switch on the main unit
manually.
No operations can be done with the remote
control.
Remove the insulation sheet before you use the
remote control for the first time. (~7)
Examine that the battery is installed correctly.
(~7)
The battery is weak. Replace it with a new one.
(~7)
Set the remote control code again after replacing
the battery. (~23)
Use the remote control within the correct operation
range. (~5)
The system automatically switched to standby
mode
“AUTO OFF” function is on.
The system automatically switches to standby mode
if there is no signal input and no operation is being
performed for approximately 20 minutes. Refer to
page 19 to switch off this function.
Bluetooth
®
Pairing cannot be done.
Check the Bluetooth® device condition.
The device is out of the 10 m communication range.
Move the device nearer to the system.
The device cannot be connected.
The pairing of the device was unsuccessful. Do
pairing again.
The pairing of the device has been replaced. Do
pairing again.
This system might be connected to a different
device. Disconnect the other device and try
connecting the device again.
The system may have a problem. Switch off the
system and then switch on again.
The device is connected but audio cannot be
heard through the system.
For some built-in Bluetooth® devices, you have to
set the audio output to “SC-HTB400” or
“SC-HTB600” manually. Read the operating
instructions of the device for details.
Sound from the device is interrupted.
The device is out of the 10 m communication range.
Move the device nearer to the system.
Remove any obstacle between the system and the
device.
Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.)
are interfering. Move the device nearer to the
system and distance it from the other devices.
HDMI
HDMI CEC related operations no longer function
properly.
Check the setting on the connected devices.
Switch on HDMI CEC function on the connected
devices.
Select this system as the speaker in the TV’s
HDMI CEC menu.
When the HDMI connections are changed, after a
power failure or after the AC mains lead has been
removed, HDMI CEC operations may not function
properly.
Switch on all the devices that are connected to
the TV with an HDMI cable and then switch on the
TV.
Switch off the HDMI CEC settings of the TV and
switch it on again. For details refer to the
operating instructions for the TV.
While the system and the TV are connected with
an HDMI cable, switch on the TV, disconnect the
AC mains lead of this system and then connect it
again.
[HTB600] The first few seconds of audio cannot be
heard when using the HDMI connection.
This may occur during DVD-Video chapter
playback. Change the digital audio output setting on
the connected device from “Bitstream” to “PCM”.
[HTB600] When the main unit is switched on or
switched off, audio and video are temporarily
disabled.
This is normal and not a malfunction. This can occur
when the connected HDMI device does not support
HDMI CEC function.
htb600.400_TQBJ2216_en.fm Page 21 Thursday, May 14, 2020 2:22 PM
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HTB600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HTB600 in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-HTB600

Panasonic SC-HTB600 User Manual - German, Dutch, French, Italian, Spanish - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info