696394
14
Zoom out
Zoom in
Previous page
1/24
Next page
14
TQBJ2086
HDMI CEC
This unit supports “HDMI CEC” (Consumer
Electronics Control) function.
See the operating instructions for connected
equipment for operational details.
Preparation
Confirm that the HDMI connection has been made.
(~9, 10)
Power on link
When the TV is switched on, the main unit also
switches on automatically. (This function does not
work when OPTICAL or Bluetooth
®
is the source.)
Power off link
When the TV is switched off, the main unit also
switches off automatically. (This function does not
work when OPTICAL or Bluetooth
®
is the source.)
Volume adjustment
You can control the volume setting of this system
using the volume or mute button on the TV remote
control.
If the TV’s speaker selection is changed to the TV
speakers, the main unit’s speakers are muted.
Muting will be cancelled by selecting the main
unit’s speakers again.
Changing speakers
When the main unit switches on, this system will
be selected as the TV’s speakers automatically.
When you switch off the main unit, TV speakers
will be automatically activated.
Note:
The operation cannot be guaranteed on all HDMI CEC
equipment.
Troubleshooting
Before requesting service, make the following
checks. If you are in doubt about some of the
check points, or if the solutions indicated do not
solve the problem, consult your dealer for
instructions.
Common problems
No power
After connecting the AC mains lead, wait about
10 seconds before switching on the main unit.
Disconnect the AC mains lead for 10 seconds
before connect again.
After switching on the main unit, if the main unit
immediately switches off, disconnect the AC mains
lead and consult your dealer.
If the main unit does not switch on when switching
on TV (HDMI CEC), switch on the main unit
manually.
No operations can be done with the remote
control.
Remove the insulation sheet before you use the
remote control for the first time. (~8)
Examine that the battery is installed correctly.
(~8)
The battery is weak. Replace it with a new one.
(~8)
Set the remote control code again after replacing
the battery. (~16)
Use the remote control within the correct operation
range. (~7)
The system automatically switched to standby
mode
“Auto power down” function is on.
The system automatically switches to standby mode
if there is no signal input and no operation is being
performed for approximately 20 minutes. Refer to
page 13 to switch off this function.
Bluetooth
®
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device is out of the 10 m communication range.
Move the device nearer to the system.
The device cannot be connected.
The pairing of the device was unsuccessful. Do
pairing again.
The pairing of the device has been replaced. Do
pairing again.
This system might be connected to a different
device. Disconnect the other device and try
connecting the device again.
The system may have a problem. Switch off the
system and then switch on again.
TQBJ2086_en.fm Page 14 Wednesday, December 27, 2017 2:30 PM
offset printing
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HTB208 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HTB208 in the language / languages: English as an attachment in your email.

The manual is 3,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info