370587
5
Zoom out
Zoom in
Previous page
1/36
Next page
5
RQT8225
[HT845] [HT885]
[Note]
To prevent the speaker cables from being pulled out of the pipes, leave the plastic wrap on the pipes while assembling the speaker stands.
[HT885] The front and surround speaker pairs as well as the pipe pairs are different.
–Check the label on the rear of the speaker before attaching the pipe ( page 6).
–The pipe with the shorter cable is for the front speaker.
1 Assemble the speaker stands.
1 Thread the speaker cable through the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the hole, and then pull
the rest of the cable through the base.
2 Insert the pipe.
3 Secure the pipe to the base.
Ensure the screws are securely fastened.
2 Attach the stands to the speakers.
Ensure the stand is fastened on straight by gradually tightening the
top and bottom screws alternately until fully tightened.
You can also attach to the lower rear of the speaker.
The height of the speaker can be changed when attaching the
stand to the upper rear or lower rear of the speaker.
3 Connect the speaker cables.
4 Secure the speaker cables to the bases.
Preventing the speakers from falling over
Preparation
Attach screw eyes (not included) to secure the speakers to the wall
(diagram right).
You will need to obtain the appropriate screw eyes to match the
walls or pillars to which they are going to be fastened.
Consult a qualified housing contractor concerning the
appropriate procedure when attaching to a concrete wall or a
surface that may not have strong enough support. Improper
attachment may result in damage to the wall or speakers.
To prevent the speaker from falling over, thread the string (not
included) from the wall to the speaker as shown and tie tightly.
[HT885]
2 Front and
2 Surround speakers
[HT885]
4 Bases
[HT885]
8 Long screws
[HT885]
8 Short screws
[HT845] 2 Front speakers
[HT845] 2Pipes
[HT845]
4 Short screws
[HT845]
4 Long screws
[HT845]
2 Bases
[HT885] 4Pipes
2kpipes with short cable:
For front speakers
2kpipes with long cable:
For surround speakers
Cable
Base
Leave the excess speaker
cable for connecting later.
Plastic wrap
Insert the pipe while gently
pulling on the speaker cable.
Pipe support
Pipe
Base
Match the groove and these
holes with the base when you
insert the pipe.
Groove
Short screws
Phillips-head
screwdriver (not included)
Before proceeding to the next step, please remove the plastic
wrap from the pipe.
Speaker
Long screws
Pipe
Twist off the vinyl ends of the
speaker cables.
§
Rear of the speaker
_: Copper
`: Silver
Push!
If there is any excess speaker cable, thread the speaker cable
into the opening near the top of the pipe while pulling the speaker
cable from the bottom of the base.
Press the speaker cable into the
groove.
§
If the speaker cables do not have vinyl
tips, directly connect them to the
terminals.
Rear side of
base
Press the speaker cable into
the base cover groove as far
as possible.
Cable
Groove
String (not included)
Wall
Screw eye (not included)
Rear of the speaker
Approx. 150 mm
[HT535]
String (not included)
WallScrew eye (not included)
Rear of the speaker
Approx. 150 mm
[HT845] [HT885]
Speaker assembly
HT535_845_885En.book Page 5 Tuesday, April 19, 2005 11:42 AM
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic sc ht 885 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic sc ht 885 in the language / languages: English as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic sc ht 885

Panasonic sc ht 885 User Manual - German - 104 pages

Panasonic sc ht 885 User Manual - Dutch, Danish - 104 pages

Panasonic sc ht 885 User Manual - French, Italian - 104 pages

Panasonic sc ht 885 User Manual - Swedish - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info