735110
15
Zoom out
Zoom in
Previous page
1/24
Next page
15
RQT0A88
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1Press [USB/CD] to select “CD”.
2While pressing and holding [SELECTOR] on the
unit, press and hold [USB/CD] on the remote
control until the unit’s display shows “REMOTE 2”.
3Press and hold [OK] and [USB/CD] on the remote
control for at least 4 seconds.
To change the mode back to “REMOTE 1”, press [USB/CD]
to select “CD” and then repeat the step 2 and 3 but replace
[USB/CD] with [ ].
Occasionally, Panasonic may release updated
software for this unit that may add or improve the way
a feature operates. These updates are available free of
charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Checking the software version
The version of the installed software is displayed.
Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
Press [OK] to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are uncertain about some of the check points, or if the
solutions indicated in the following guide does not resolve
the issue, then consult your dealer for instructions.
Cannot turn on the unit.
After connecting the AC mains lead, wait about 10 seconds before
turning on the unit.
Humming heard during playback.
If an AC mains lead or fluorescent lights are near the cords, then
keep other appliances and cords away from the cables.
The unit does not work.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1Press [Í/I] on the unit to switch the unit to standby.
If the unit does not switch to standby, press [Í/I] on the unit
for approximately 10 seconds. The unit is forcibly switched
to standby. Alternatively, disconnect the AC mains lead, wait
for at least 3 minutes, then reconnect it.
2Press [Í/I] on the unit to switch it on. If the unit still cannot be
operated, consult the dealer.
MP3 cannot be read.
You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
When creating a multi-session disc, it is necessary to close the
session.
The amount of data on the disc is too small. Set the amount of
data to above 5 MB.
Charging does not start during standby mode.
Turn the unit on. Check the charging has started, and then turn
the unit to standby mode. (l6)
Noise is heard.
When a device is connected to both the AUX IN jack and the DC
OUT terminal, noise may be generated depending on the device.
In this case, remove the USB cable from the DC OUT terminal.
Changing the unit and remote
control code
Software update
To return all settings to the factory defaults
When the following situations occur, reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
1Disconnect the AC mains lead. (Wait for at least
3 minutes before proceeding to step 2.)
2While pressing and holding down [Í/I] on the
unit, reconnect the AC mains lead.
Keep holding down [Í/I] until “---------” appears on the
display.
3Release [Í/I].
All the settings are returned to the factory defaults. You will
need to reset the memory items.
General
SC-HC397-395EGEBGN~RQT0A88-1B.book 15 ージ 207年月5 木日 前134分
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HC397 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HC397 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-HC397

Panasonic SC-HC397 User Manual - German, French, Italian, Finnish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info