563928
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
RQT9869
Main unit displays
“--:--”
You connected the AC mains lead for the first time or there
was a power failure recently. Set the clock.
“ADJUST CLOCK”
The clock is not set. Adjust the clock.
“ADJUST TIMER”
The play timer is not set. Adjust the play timer.
“AUTO OFF”
The system has not been used for 20 minutes and will
switch off within a minute. To cancel, press any button.
“ERROR”
An incorrect operation was done. Read the instructions and
try again.
“F61”
“F77”
Disconnect the AC mains lead and consult your dealer.
“F70”
Examine the Bluetooth
®
device.
Disconnect the Bluetooth
®
device. Switch off the system
and then switch on again.
“F76”
There is a problem with the power supply.
Disconnect the AC mains lead and consult your dealer.
“ILLEGAL OPEN”
The sliding door is not in a correct position. Switch off the
system and then switch on again.
“NODEVICE”
The USB device is not connected. Examine the connection.
“NO DISC”
You have not put in a disc.
“NO MEMORY”
DAB memory presetting has not been done.
“NO PLAY”
Examine the content. You can only play supported format.
The system may have a problem. Switch off the system and
then switch on again.
“NO SIGNAL”
The station cannot be received. Adjust the antenna.
“PLAYERROR”
You played an unsupported MP3 file. The system will skip
that track and play the next one.
“REMOTE 1”
“REMOTE 2”
The remote control and the main unit are using different
codes. Change the code of the remote control.
When “REMOTE 1” is shown, press and hold [OK] and
[ ] for a minimum of 4 seconds.
When “REMOTE 2” is shown, press and hold [OK] and
[USB/CD] for a minimum of 4 seconds.
“SCAN FAILED”
Stations cannot be received. Adjust the antenna or do
manual tuning.
“USB OVER CURRENT ERROR”
The USB device is using too much power. Disconnect the
USB device, switch off the system and then switch on again.
“VBR–”
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [USB/CD] to select “CD”.
To set the code to “REMOTE 2”
1 Press and hold [SELECTOR] on the main unit and
[USB/CD] on the remote control.
“REMOTE 2” is shown.
2 Press and hold [OK] and [USB/CD] for a minimum of
4 seconds.
To set the code to “REMOTE 1”
1 Press and hold [SELECTOR] on the main unit and
[ ] on the remote control.
“REMOTE 1” is shown.
2 Press and hold [OK] and [ ] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
1 Disconnect the AC mains lead.
2 While you press and hold [1] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
–––––––– is shown.
3 Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
SC-HC29 DBEB.GN.GS RQT9869-2B EN.fm Page 14 Friday, April 18, 2014 10:45 AM
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-HC29 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-HC29 in the language / languages: English as an attachment in your email.

The manual is 2,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-HC29

Panasonic SC-HC29 User Manual - English - 20 pages

Panasonic SC-HC29 User Manual - Danish, Polish - 88 pages

Panasonic SC-HC29 User Manual - Portuguese - 20 pages

Panasonic SC-HC29 User Manual - Swedish, Spanish, Finnish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info