533596
43
Zoom out
Zoom in
Previous page
1/52
Next page
Reference
Optional speaker
settings
43
VQT3D27
Reference
Troubleshooting guide
Before requesting service, please perform the
following steps.
The following do not indicate a problem with this unit:
jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
Unit does not respond to the remote
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
To return to the factory preset
Select “Yes” in “Restore Default Settings” in the Setup menu.
(> 40)
To return all settings to the factory preset
Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn’t work properly.
Change the batteries in the remote control. (> 9)
The remote control and main unit are using different codes. If
“SET is displayed on the unit’s display when a button is
pressed on the remote control, change the code on the
remote control. (> 40)
Disc cannot be played.
The disc is dirty. (> 9)
Check the region code.
Still pictures (JPEG) do not playback normally.
The images that were edited on the PC, such as Progressive
JPEG, etc., may not playback.
The TV tuner mode is not displayed when the TV is
switched on.
This phenomenon may occur, depending on the TV setting,
when “Quick Start” is set to “On”.
Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] and [Y] on the
remote control at the same time for more than 5 seconds.
j00 RET” is displayed on the unit’s display.
2
Repeatedly press [
1
] (right) on the remote control or
[POWER
Í
/I] on the unit until “03 VL” is displayed on the
unit’s display.
3 Press [OK] on the remote control or [< OPEN/CLOSE] on
the unit.
This unit does not recognize the communication camera
correctly.
Disconnect and reconnect the communication camera. If it
still does not recognize the connection, turn the power of this
unit off and on again.
No power.
Insert the AC power supply cord securely into a household
AC outlet. (> 18)
The unit switches to standby mode.
This unit will automatically turn to standby mode after 30
minutes if it is inactive. (> 7)
When the time set for the sleep timer has passed, the power
will be turned off. (> 6)
One of the unit’s safety devices is activated. Press
[POWER Í/I] on the main unit to turn the unit on.
This unit is turned off when the input for the TV is switched.
This is a normal phenomenon when using VIERA Link
(HDAVI Control 4 or later). For details please read the
operating instructions for the TV.
The unit does not turn off.
1
Press and hold [POWER
Í
/I] on the main unit for 5 seconds.
(If still unable to power the unit off, disconnect the power
cord, wait 1 minute, then reconnect the power cord.)
2 Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME],
[< OPEN/CLOSE] and [POWER Í/I] on the main unit at
the same time for more than 5 seconds.
The display is dim.
Change “Front Panel Display” in the Setup menu. (> 38)
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies. (> 22)
4
Make the following checks and visit our
website for more information.
For U.S.A. :
http://www.panasonic.com/help
Enter the model number.
For Canada :
http://www.panasonic.ca
4
Or visit our website to find a service
center.
You can find a service center near you easily on our website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” (> 50) or “Limited Warranty (Only for CANADA)”
(> 51)
General operation
Power
Displays
VQT3D27~Body_mst.fm 43 ページ 2010年12月24日 金曜日 午後6時48分
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-BTT273 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-BTT273 in the language / languages: English as an attachment in your email.

The manual is 9,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info