602097
47
Zoom out
Zoom in
Previous page
1/60
Next page
47
RQT9508
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 58 if you reside in the U.S.A.and Puerto
Rico, or refer to “Product information” on page 59 if you reside in Canada. In other areas, consult your dealer.
The following do not indicate a problem with this unit:
Regular disc rotating sounds.
Image disturbance during search.
To reset this unit Page
Power
Operation
To restore the unit if it freezes
due to one of the safety
devices being activated.
Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings remain
unchanged.)
To return all settings other than
some settings to the factory
preset.
Select “Yes” in “Restore Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for “Remote
Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server Settings”,
“Network Service”, “DVD-Video Ratings” and “BD-Video Ratings” to the default settings.
40
To return to the factory preset.
(No setting)
Reset the unit as follows:
1 Press [POWER Í/I] on the unit to turn off the unit.
2 Press and hold [5/9] and press [POWER Í/I] and [< OPEN/CLOSE] on the unit at
the same time for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.
3 The power is turned on and then turned off automatically.
No power. Insert the AC power supply cord securely into a household AC outlet. 14
The unit switches to standby
mode.
This is a power saving feature. It can be changed if desired using “Off Timer” in the Setup
menu.
When the time set for the sleep timer has passed, the power will be turned off.
One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the
unit on.
40
21
Power of this unit is turned off
when the input for the TV is
changed.
If connected with an HDAVI Control 4 compatible TV (VIERA) with the “Auto power stand-by”
setting activated on the TV, when switching the TV input, the unit will be automatically turned
to standby if the TV audio is not output from the unit’s speakers. For details please read the
operating instructions of the TV.
29
The remote control doesn’t
work properly.
The remote control and main unit are using different codes.
Change the code on the remote control.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
The batteries are depleted. Replace them with new ones.
It may be necessary to set the code of the remote control again after changing the batteries
for remote control.
You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
Colored glass may obstruct the signal reception/transmission.
Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
50
5
50
5
The unit is on but cannot be
operated.
Confirm the correct drive is selected.
Some operations may be prohibited by the disc.
The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [POWER Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main unit for
about 3 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.
2 Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be operated,
consult the dealer.
Condensation has formed. Wait 1 to 2 hours for it to evaporate.
17
52
Play fails to start even when
[1PLAY] is pressed.
Play starts but then stops
immediately.
Insert the media correctly with the label facing up.
The media is dirty.
You tried to play a blank media or unplayable media on this unit.
The producers of the disc can control how discs are played. So you may not always be able
to control play as described in these operating instructions. Read the disc’s instructions
carefully.
19
43
42, 43
Cannot eject disc. The unit may have a problem. While the unit is off, press and hold [5/9] and [< OPEN/
CLOSE] on the main unit at the same time for about 5 seconds. Remove the disc and consult
the dealer.
Startup is slow.
It takes time before play starts.
Startup takes time in the following situations.
Immediately after a power failure or the AC power supply cord is connected.
When the unit is connected with an HDMI cable.
Played back image is distorted
or does not playback correctly.
([AVCHD])
High definition video (transfer rate of 18 Mbps or faster) cannot be played back correctly if it
was recorded on a DVD compatible to double speed or slower.
Cannot set “On” in “24p
Output”.
Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select
“On”.
39
Reference
BT300.book 47 ページ 2009年6月12日 金曜日 午後12時13分
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-BT303 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-BT303 in the language / languages: English as an attachment in your email.

The manual is 15,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info