602096
51
Zoom out
Zoom in
Previous page
1/60
Next page
51
RQT9508
Messages
The following messages or service numbers appear on the TV or unit’s display when something unusual is detected during startup and use.
On the TV Page
Cannot play. You inserted an incompatible disc (Discs recorded in PAL video, etc.). 42, 43
Cannot display on this unit. You tried to play a non-compatible image. 43, 44
No disc is inserted. The disc may be upside down.
$ This operation is not
available.
Some operations are prohibited by the unit or disc. For example;
[BD-V]
: During play back, reverse slow-motion or reverse frame-by-frame is not possible.
$ This operation is prohibited
by this disc.
Depending on the disc, you may not be able to perform search or skip when film previews
and warning screens are being played back.
Cannot connect.
Please check the connection of
the LAN cable.
When a hub is used but its Link lamp does not light up, check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
14
IP address is not set. The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---”. Set the “IP Address”,
“Subnet Mask”, and “Default Gateway. (Select the automatic address acquisition if
necessary.)
33
Cannot obtain IP address using
DHCP.
Please check the connection or
router settings.
If you use a hub, then check the connection between the hub and the router.
Use the UPLINK port of the hub to connect to a router.
Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
14
14
This IP address is already in
use.
Please check the IP address
setting.
This unit’s IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
Unable to perform Connection
Test.
Please try again.
Turn the unit off. Remove the power cord and reconnect it and try again. If the same
symptom persists, then consult your dealer.
IP address not set correctly.
Connection Test was
unsuccessful. No reply
from host.
Please check the connection or
router settings.
If you use a hub, then check the connection between the hub and the router.
Use the UPLINK port of the hub to connect to a router.
If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS
Settings”.
If the MAC address information is required, then press [SETUP] to display the “Network”
menu.
14
33
33
Network connection refused.
Please confirm Setup “BD-Live
Internet Access.”
When you set “BD-Live Internet Access” to “Allow ( Limited )” and play BD-Live contents
which do not have a content owner certificate, the Internet access of the content is not
allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to
“Allow ( ALL )”.
37
Unable to check for latest
firmware version.
Please try again later.
The firmware download server is currently unavailable. Please try again later.
High Clarity Sound is effective.
Analog video output is turned
off when
playback starts.
“High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in
on-screen menu is set to “On”.
36, 38
No Video Depending on the connected iPod, video menu may not be available on the TV. Select the
iPod menu (iPod LCD) mode and operate video playback from your iPod menu.
31
On the units display
F99 The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [POWER Í/I] on the main unit again to turn the unit on.
HDMI ONLY Some BD-Video discs can only be output with HDMI.
NET Displays while VIERA CAST is starting up.
No PLAY There is a viewing restriction on a BD-Video or DVD-Video. 37
No READ The media is dirty or badly scratched. The unit cannot play.
PLEASE WAIT The unit is carrying out internal process.This is not a malfunction. You cannot operate the
unit while “PLEASE WAIT” is displayed.
When connected to a TV (VIERA) with HDAVI Control 4, and power supply is turned off by
the “Auto power stand-by” function on the TV side.
SET
(“ stands for a number.)
The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
50
UNFORMAT You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format).
UNSUPPORT You have inserted a media the unit cannot play. 42, 43
Reference
BT300.book 51 ページ 2009年6月12日 金曜日 午後12時13分
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-BT300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-BT300 in the language / languages: English as an attachment in your email.

The manual is 15,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info