492359
54
Zoom out
Zoom in
Previous page
1/56
Next page
54
RQT9224
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies
indicated in the chart do not solve the problem, consult your dealer for instructions.
Pages
No power. • Ensure the AC mains lead is connected. 12, 13
No sound.
Sound is distorted.
• Check that the volume is adequate.
Select either “SPEAKERS A ” or “SPEAKERS B ” if the speakers indicator is off.
• Select the correct input source.
• Cancel the “MUTING ” function.
• Check that the signals can be decoded by this unit.
• Check connections to speakers and other equipment.
• Check that the input setting suits the type of connection you have made.
• Cancel the PCM FIX.
• Recording of some DVD-Audio may not be possible to be played due to
copyright protection.
15, 26
24, 26, 27
15, 26
31
50
10 to 13, 16 to 23
39
39
Sound stops.
F61 appears on the display
for about a second, and the unit
turns off.
• Check that
(
and
)
of speaker cable is interfering each other.
• Check that speaker impedance is lower than tolerance of the unit.
• Straining of the speakers through excessive volume or power.
• This may occur if you use the unit in an extremely hot environment.
• Curtains or other objects may be blocking the exhaust hole.
Ö
Determine and correct the cause, then turn the unit on.
(The protection circuit is reset.)
(Consult your dealer if the problem persists.)
10
10, 22
F76 appears on the display
and the unit turns off.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
F70 appears on the display. • Turn the unit off, disconnect the AC mains lead, and consult your dealer.
Display is dim. • Cancel “DIMMER”. 37
Clicking sound is heard during
play.
• Depending on the input signal when playing DVD etc., the BI-AMP
function changes automatically. A clicking sound is heard when it changes.
This does not mean a problem with the unit.
MEASURING ERROR appears
on the display.
• A speaker is too far. Check speaker locations.
• An error occurred from a cause that cannot be identi ed. Perform the auto
speaker setup again.
24, 25
When speaker distances are set
(
page 37), appears on the
display with the speaker name
such as L 3.0 – ”.
• It appears when polarity of a speaker is automatically adjusted.
You can set speakers against automatic polarity adjustment. 38
When speaker distances are set
(
page 37), OVER appears
on the display.
• It appears when the measured distance exceeds 15 meters.
Check the speaker location.
Sound is not heard from the
center, surround or subwoofer
speakers.
• Ensure the speaker settings for your speakers are correct.
• Con rm Dolby Pro Logic
, NEO:6, or SFC settings, and select an
adequate mode.
• Press [SURROUND] on when you play 2-channel stereo sources.
24, 25, 37
28 to 30
13, 29
Sound is not heard from the
surround back speaker.
• Ensure the speaker settings for your speakers are correct.
• Press [SURROUND] on.
24, 25, 37
13, 29
Dolby Pro Logic
, NEO:6, and
SFC are unavailable.
• Check if the center speaker, surround speakers, and surround back
speakers are connected properly.
• Press [SPEAKERS A] on.
• Cancel ANALOG 8CH playback.
• You cannot use the effect when the input source contains dual audio
signals in Dolby Digital or DTS formats.
10, 11
26
27
There is no DTS audio output.
There is audio output, but the
DTS decoder indicator is not lit.
• Set the DTS Digital Audio Output setting on the Blu-ray Disc/DVD player
or DVD recorder to “Bitstream”.
The radio cannot be tuned in
or there is a lot of noise and
interference.
Connect the appropriate antenna. (You may need an outdoor antenna or one with more elements.)
• Adjust the position of the FM or AM antenna.
• Reduce the treble.
• Turn off nearby televisions, video decks, DVD recorders, Blu-ray Disc/DVD
players, and satellite receivers.
• Separate the antenna from other cables, cords, and appliances.
23
23
34
There is a lot of noise when
listening to AM.
• Try changing the BEAT PROOF mode. 47
The correct AM frequency
cannot be tuned in.
• Change the frequency step to suit your area when AM is selected. 47
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SA-BX500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SA-BX500 in the language / languages: English as an attachment in your email.

The manual is 9,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SA-BX500

Panasonic SA-BX500 User Manual - German - 56 pages

Panasonic SA-BX500 User Manual - Dutch - 56 pages

Panasonic SA-BX500 User Manual - Danish - 56 pages

Panasonic SA-BX500 User Manual - French - 56 pages

Panasonic SA-BX500 User Manual - Italian - 56 pages

Panasonic SA-BX500 User Manual - Polish - 56 pages

Panasonic SA-BX500 User Manual - Swedish - 56 pages

Panasonic SA-BX500 User Manual - Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info