536677
94
Zoom out
Zoom in
Previous page
1/115
Next page
LAMP and WARNING Indicators
Managing the indicated problems
If a problem should occur inside the projector, the <ON(G)/STANDBY(R)>, <LAMP> and/or <WARNING> indicators will inform
you. Manage the indicated problems as follow.
Attention
Before you take a remedial measure, follow the procedure of switching the power off indicated in “Powering Off the f
projector”. (
Æ
page 37)
LAMP indicator
Indicator Lighting in red. Flashing in red.
Status Time to replace the lamp unit.
A problem is detected in the lamp or the power supply for the
lamp.
Check
Was [REPLACE LAMP] displayed when f
you turned on the power?
The indicator lights up when the f
runtime of the lamp unit has reached
4 000 hours (when [LAMP POWER] is
set to [NORMAL]).
Have you turned on the f
power again immediately
after turning it off?
Some error has occurred in f
the lamp circuit. Check for
uctuation (or drop) in the
source voltage.
Remedy Replace the lamp unit. f
Wait a while until the f
luminous lamp cools off,
and then turn on the power.
Turn off the projector, and f
unplug the AC power cord,
and consult your dealer.
Note
Contact your dealer for repair services when <LAMP> indicator persists to light after taking these measurements. f
WARNING indicator
Indicator Lighting in red. Flashing in red. Flashing in red. (Slow)
Status Internal temperature is high (warning).
Internal temperature is high
(standby status).
The projector detects an
abnormal condition and
cannot be turned on.
Check
Is the air intake/exhaust port blocked? f
Is the room temperature high? f
Is the air lter unit clogged? f
_
Remedy
Remove any objects that are blocking the air intake/ exhaust port. f
Install the projector in a location with an ambient temperature of 0 °C f
(32 °F) to 40 °C (104 °F)
Do not use the projector at high altitudes of 2 700 m (8 858 f ') or higher
above sea level.
Replace the air lter unit. ( f
Æ
page 95)
If the projector is turned off f
again, unplug the AC power
cord and contact the dealer
or the service center for
service and checkup.
Note
If <WARNING> indicator persists to light or blink after taking these measurements, please contact your dealer for repair f
services. Do not leave the projector on. It may cause an electric shock or a re hazard.
The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on f
the projector. If the projector is turned off again, unplug the AC power cord and contact the dealer or the service center for
service and checkup. Do not leave the projector on. It may cause an electric shock or a re hazard.
<LAMP> indicator
<WARNING> indicator
94 - ENGLISH
Chapter 5 Maintenance - LAMP and WARNING Indicators
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-VX410Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-VX410Z in the language / languages: English as an attachment in your email.

The manual is 17,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info