536677
36
Zoom out
Zoom in
Previous page
1/115
Next page
Connect the power cord to the projector body.1)
Connect the power plug to an outlet.2)
The power indicator <ON(G)/STANDBY(R)> lights or blinks, and the projector will enter the standby mode. f
Press the <3) v/b> button on the control panel or on the remote control.
The power indicator <ON(G)/STANDBY(R)> lights in green and the image is soon projected on the screen. f
Attention
Using the projector while the lens cap is attached may cause the device to heat up and result in a re. f
Note
If the [PROJECTOR SETUP] menu f → [ECO MANAGEMENT]→[STANDBY MODE] is set to [ECO], it may take approx. 10
seconds longer before the projector starts projecting after the power is turned on, compared with when [NORMAL] is set.
Making adjustments and selections
It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted.
3)
5)
3)
Adjust the focus of the image roughly. (1) Æpage 38)
Change the settings of the [PROJECTOR SETUP] menu → [PROJECTION METHOD] depending on 2)
the installation mode. (Æpage 25)
Refer to “Navigating through the menu” ( f Æ page 45) for the operation of the menu screen.
Press the <INPUT SELECT> button on the control panel or the input selection (<COMPUTER 1>, 3)
<COMPUTER 2>, <HDMI>, <VIDEO>,<S-VIDEO>) buttons to select the input signal.
Adjust the front, back and sideway tilt of the projector with the adjustable feet. (4) Æpage 28)
If the input signal is an analog RGB signal, press the <AUTO SETUP> button.5)
Adjust the size of the image to match the screen with the zoom ring.6)
Adjust the focus with the focus ring.7)
Note
When the projector is switched on for the rst time after purchase as well as when the [PROJECTOR SETUP] menu → f
[INITIALIZE ALL] is executed, the initial setting screen is displayed after projection starts. Refer to “Start-up display” for
details. (Æ page 19)
Powering On the Projector
Before switching on the projector, make sure all the other devices are correctly connected (Æpages 31-32 ) and remove the
lens cap.
3)
3)
2)1)
36 - ENGLISH
Chapter 3 Basic Operations - Powering on/off
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-VX410Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-VX410Z in the language / languages: English as an attachment in your email.

The manual is 17,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info