511537
32
Zoom out
Zoom in
Previous page
1/127
Next page
Chapter 3 Basic Operations — Switching on/off the projector
32 - ENGLISH
Indicator status Status
Off The main power is switched off.
Red
Flashing
The power is switched off (in standby mode). [STANDBY MODE] is set to [NORMAL].
Projection will start when the power <
v
/
b
> button is pressed.
f
The projector may not operate when the temperature indicator <TEMP> is ashing.
(
x
page 108)
Lit
The power is switched off (in standby mode). [STANDBY MODE] is set to [ECO].
Projection will start when the power <
v
/
b
> button is pressed.
f
The projector may not operate when the temperature indicator <TEMP> is ashing.
(
x
page 108)
Green Lit Projecting.
Note
f
The projector consumes power even in standby mode (the power indicator <ON (G)/STANDBY (R)> lights/ashes in red).
Refer to “Power consumption” (
x
page 122) for the power consumption.
f
The power indicator <ON (G)/STANDBY (R)> ashes in green if a remote control signal is received.
f
The power indicator <ON (G)/STANDBY (R)> ashes in green slowly when the projector is in AV mute mode.
Switching on the projector
1)
3)
2)
3)
1)
Connect the power plug to an outlet.
f
(AC 100 V - 240 V 50 Hz/60 Hz)
2)
Press the <ON> side of the <MAIN POWER> switch to turn on the power.
f
The power indicator <ON (G)/STANDBY (R)> lights/ashes in red, and the projector enters the standby mode.
3)
Press the power <v/b> button.
f
The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Note
f
If the projector is switched on at around 0 °C (32 °F), a warm-up period of approximately ve minutes may be necessary until an image is
displayed.
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “Managing the indicated problems” (
x
page 108) for the indicator status.
f
If the operating environment temperature is low and warm-up takes more than ve minutes, the projector will judge that a problem has
occurred and the power will automatically be set to standby mode. If this happens, increase the operating environment temperature to 0 °C
(32 °F) or higher, turn off the main power, and then turn on the power again.
f
If the [PROJECTOR SETUP] menu
[ECO MANAGEMENT]
[STANDBY MODE] (
x
page 70) is set to [ECO], there may be a delay in
displaying when the power is turned on compared to when the setting is [NORMAL].
f
When the power is turned or an input signal is switched, you may here a high-frequency driving sound. This is not a malfunction.
f
If the [PROJECTOR SETUP] menu → [INITIAL STARTUP] (
x
page 73) is set to [LAST MEMORY] and the power is turned off by pressing
the <OFF> side of the <MAIN POWER> switch or by using the breaker directly while projecting at the last time of use, the power indicator
<ON (G)/STANDBY (R)> lights in green and projection starts after a while when the power is turned on by pressing the <ON> side of the
<MAIN POWER> switch with the power plug connected to the outlet, or when the breaker is turned on.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-RZ370E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-RZ370E in the language / languages: English as an attachment in your email.

The manual is 15,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-RZ370E

Panasonic PT-RZ370E Additional guide - German - 11 pages

Panasonic PT-RZ370E User Manual - German - 130 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info