511568
35
Zoom out
Zoom in
Previous page
1/138
Next page
Chapter 3Basic Operations — Switching on/off the projector
ENGLISH - 35
Indicator status Projector status
Off The main power is switched off.
Red
Flashing
The power is switched off (in standby mode). [STANDBY MODE] is set to [NORMAL].
Projection will start when the power <v/b> button is pressed.
f The projector may not operate when the temperature indicator <TEMP> is ashing.
Lit
The power is switched off (in standby mode). [STANDBY MODE] is set to [ECO].
Projection will start when the power <v/b> button is pressed.
f The projector may not operate when the temperature indicator <TEMP> is ashing.
Green Lit Projecting.
Note
f The projector consumes power even in standby mode (the power indicator <ON (G)/STANDBY (R)> lights/ashes in red). Refer to “Power
consumption” (x page 133) for the power consumption.
f The power indicator <ON (G)/STANDBY (R)> ashes in green if a remote control signal is received.
f The power indicator <ON (G)/STANDBY (R)> ashes in green slowly when the projector is in AV mute mode.
Switching on the projector
2)
4)
3)
4)
1)
1) Connect the power cord to the projector body.
2) Connect the power plug to an outlet.
f (AC 100 V - 240 V 50 Hz/60 Hz)
3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.
f The power indicator <ON (G)/STANDBY (R)> lights/ashes in red, and the projector enters the standby mode.
4) Press the power <v/b> button.
f The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Note
f If the projector is switched on at around 0 °C (32 °F), a warm-up period of approximately ve minutes may be necessary until an image is
displayed.
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “When an indicator lights up” (x page 119) for the indicator status.
f If the operating environment temperature is low and warm-up takes more than ve minutes, the projector will judge that a problem has
occurred and the power will automatically be set to standby mode. If this happens, increase the operating environment temperature to 0 °C
(32 °F) or higher, turn off the main power, and then turn on the power again.
f If the [PROJECTOR SETUP] menu [ECO MANAGEMENT] [STANDBY MODE] is set to [ECO], it may take more time before the
projector starts projecting after the power is turned on compared with when [NORMAL] is set.
f When the power is turned or an input signal is switched, you may here a high-frequency driving sound. This is not a malfunction.
f If the [PROJECTOR SETUP] menu [INITIAL STARTUP] is set to [LAST MEMORY] and the power is turned off by pressing the <OFF>
side of the <MAIN POWER> switch or by using the breaker directly while projecting during the last time of use, the power indicator <ON
(G)/STANDBY (R)> lights in green and projection starts after a while when the power is turned on by pressing the <ON> side of the <MAIN
POWER> switch with the power plug connected to the outlet, or with the breaker turned on.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-RW430EW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-RW430EW in the language / languages: English as an attachment in your email.

The manual is 18,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-RW430EW

Panasonic PT-RW430EW User Manual - German - 144 pages

Panasonic PT-RW430EW User Manual - French - 143 pages

Panasonic PT-RW430EW User Manual - Italian - 143 pages

Panasonic PT-RW430EW User Manual - Spanish - 141 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info