536686
50
Zoom out
Zoom in
Previous page
1/70
Next page
About indicator status
50
- ENGLISH
Maintenance
Maintenance
About indicator status
If an indicator turns on
If a problem should occur inside the projector, the <TEMP> and/or <LAMP> indicators will inform you. Manage
the indicated problems as follow.
Attention
Before you take a remedial measure, follow the procedure of switching the power off indicated in “Powering off the
z
projector”. (
Æ
page 27)
Conrm the status of the power indicated on the <ON(G)/STANDBY(R)> indicator. (
z
Æ
page 26)
<LAMP> indicator
<TEMP> indicator
<TEMP> indicator
J
Indicator
status
Status Check Remedy
Lights in
red
Temperature
too high
Is the air intake/exhaust
port blocked?
Remove any objects that are blocking the air intake/exhaust port.
Are the air lters
blocked?
See air lters cleaning or replacing. (
Æ
pages 51-53)
Is the room
temperature high?
Set up the projector in a location with an ambient temperature of
5°C (41°F) to 40°C (104°F)*.
Is the projector used
above the altitude of
1 000 m
(3 300 ft)
?
- Use the projector between the altitude approx. 1 000 m
(
3 300
ft) and approx. 3 000 m (10 000 ft) and set [High Altitude]
to [On]. (
Æ
page 42)
-
Do not use the projector at elevations approx. 3 000 m (10 000 ft).
Blinks in
red
The fan has
stopped
--
Disconnect the power plug from the power outlet and contact your
dealer.
* For the elevations below approx. 750 m (2 500 ft). When using the projector at the elevations between approx.
750 m (2 500 ft) and approx. 1 500 m (5 000 ft) sea level, temperature will be
5
°C (
41
°F) to 35°C (95°F). When
using the projector at the elevations between approx. 1 500 m (5 000 ft) and approx. 3 000 m (10 000 ft) sea
level, temperature will be
5
°C (
41
°F) to 30°C (86°F).
<LAMP> indicator
J
Indicator
status
Status Check Remedy
Lights in red
Lamp does not
light; or lights out
during projection
Does the projector be turned on
immediately after powering off?
Turn on the projector until the lamp has
completely cooled down.
Lamp unit failure; abnormal lamp
power; lamp broken
Disconnect the power plug from the power
outlet, and contact your dealer.
Note
When re-start the projector, turn off the projector, unplug the power cord, and then wait 30 seconds or more before
z
reconnecting power.
If the <TEMP> indicator lights or ashes or the <LAMP> indicator lights despite taking the actions above, plug out the AC
z
power cord, and contact your dealer for repair.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-LW271E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-LW271E in the language / languages: English as an attachment in your email.

The manual is 6,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-LW271E

Panasonic PT-LW271E User Manual - Spanish - 70 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info