598931
120
Zoom out
Zoom in
Previous page
1/130
Next page
120 - ENGLISH
Chapter 6 Appendix — Technical information
Sync. method Asynchronous
Baud rate 9 600 bps
Parity None
Character length 8 bit
Stop bit 1 bit
X parameter None
S parameter None
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according
to the details of control.
E\WHV
,'FKDUDFWHUV
E\WHV
6HPLFRORQ
E\WH
&RORQE\WH
&RPPDQG
FKDUDFWHUVE\WHV
3DUDPHWHU
XQGHILQHGOHQJWK
(QGE\WH
6WDUWE\WH
==±DQG$±=
,'VHWWLQJDUHD
Attention
rf
If a command is transmitted after the lamp starts illuminating, there may be a delay in response or the command may not be executed. Try
sending or receiving any command after 60 seconds.
rf
When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the response from the projector before
sending the next command. When transmitting a command which does not need a parameter, a colon (:) is not necessary.
Note
rf
If a command cannot be executed, an “ER401” response is sent from the projector to the computer.
rf
If an invalid parameter is sent, an “ER402” response is sent from the projector to the computer.
rf
ID transmission in RS-232C supports ZZ (ALL) and 01 to 64, as well as 0A to 0Z groups.
rf
If a command is sent with a specied ID, a response will be sent to the computer only in the following cases.
rg
It matches the projector ID
rg
ID setting is set to ALL and [RESPONSE(ID ALL)] is [ON]
rg
ID setting is set to GROUP and [RESPONSE(ID GROUP)] is [ON]
rf
STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.
When multiple projectors are controlled
When multiple projectors are all controlled
When controlling multiple projectors together via RS-232C, perform the following settings.
1)
Set a different ID for each projector.
2)
Set [RESPONSE(ID ALL)] to [ON] in only one
projector.
3)
Set [RESPONSE(ID ALL)] to [OFF] for all other
projectors set in Step 2).
When multiple projectors are all controlled by group unit
When controlling multiple projectors by group unit via RS-232C, perform the following settings.
1)
Set a different ID for each projector.
2)
Set [RESPONSE(ID GROUP)] to [ON] in only
one projector.
3)
Set [RESPONSE(ID GROUP)] to [OFF] for all
other projectors set in Step 2).
Note
rf
There will be no response if 2 or more projectors have [RESPONSE(ID ALL)] set to [ON].
rf
There will be no response if 2 or more projectors of the same group have [RESPONSE(ID GROUP)] set to [ON].
rf
When setting multiple groups, set [RESPONSE(ID ALL)] to [ON] in only one projector in each group.
120


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DZ680EL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DZ680EL in the language / languages: English as an attachment in your email.

The manual is 16,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DZ680EL

Panasonic PT-DZ680EL User Manual - German - 137 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info