543659
28
Zoom out
Zoom in
Previous page
1/50
Next page
ENGLISH - 28
Maintenance
Monitor Lamp indicators
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow.
1. Confirm the status of all indicators and projector, and switch off the projector in proper way.
2. Find out the cause of the problem by status of each indicator.
3. Follow the instruction for each indication below and solve the problem.
4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.
J LAMP1/LAMP2 indicator
J TEMP indicator
Managing the indicated problems
NOTE:
If no problem is found or the problem remains, do not turn on the projector. Instead contact an Authorized Service Center.
Lamp
indication
Information Check point Remedial measure
Lighting in red
Indicates the time for
replacing the lamp unit
Did you notice a “REPLACE
LAMP” message on the screen
when turning on the projector
power supply?
This lamp monitor lights up when the lamp
unit used hours have reached 1 800 hours.
Request the dealer to replace the lamp unit.
Blinking in red
once
Lamp unit is not installed.
Check the lamp unit
compartment.
Install the lamp unit.
When lamp unit is installed and still having
the indicator lights, contact to the dealer.
Blinking in red
3 times
Error is detected in the
lamp circuit.
Did you turn the power back on
immediately after turning it off?
Wait until the lamp has cooled off, and then
turn on the power.
Some error has arisen in the
lamp circuit.
Check for fluctuation (or drop) in
the source voltage.
Turn off the POWER switch of the projector
in proper way and contact the dealer.
Lamp
indication
Information Check point Remedial measure
Lighting in red
Warm-up status
Did you turn on the power when
the ambient temperature was
lower than approx. 0 °C (32 °F)?
Wait about 5 minutes in the current status.
Install the unit in a location having an
ambient temperature from 0 °C (32 °F) -
45 °C (113 °F).
High temperature inside.
(WARNING)
Check the ventilation port is
blocked.
Is the room air temperature too
high?
Was the temperature warning
indication displayed?
Remove the object that is blocking the
ventilation port.
Move the projector to a temperature of 0 °C
(32 °F) - 45 °C (113 °F) and the humidity of
20 % to 80 % (no condensation).
Turn off the POWER switch of the projector
in proper way and contact the dealer.
Blinking in red
twice
High temperature inside.
(Standby condition)
Blinking in red
3 times
Cooling fan has been
stopped.
Turn off the POWER switch of the projector
in proper way and contact the dealer.
STANDBY(RED)/STANDBY(RED)/
ON(GREEN) ON(GREEN)
LAMPLAMP TEMPTEMP
FILTERFILTER
STANDBY(RED)/
STANDBY(RED)/
ON(GREEN)
ON(GREEN)
LAMP
LAMP
TEMP
TEMP
FILTER
FILTER
Indicators
Power indicator
Lamp1 (LAMP1) indicator
Lamp2 (LAMP2) indicator
Temperature (TEMP) indicator
Filter (FILTER) indicator
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DZ6700U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DZ6700U in the language / languages: English as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info