511534
56
Zoom out
Zoom in
Previous page
1/179
Next page
Projecting
56 - ENGLISH
Basic Operation
When a projection lens with a large weight is installed, or when the projector is installed in an inclination, the lens
may tilt and the focus may become unbalanced. In these cases, refer to Figure 3 and the adjustment examples in
the table below, and perform adjustments through the following procedures.
z
Adjustment procedure
1) Press the <FOCUS> button or the <LENS> button on the remote control on the
control panel to display the focus adjustment menu.
2) Shift the focus of the entire screen once pressing
.
3) Press
to stop on any part of the screen to be the rst just focus point.
z
For the location where focus is shifted in this state, the just focus point is in the inner side of the screen.
4) Loosen the xed screws in the position relative to the location where the focus is
shifted the most (the location where the just focus point is shifted the most towards
the inner side in Step 2)) up to two rotations (see Figure 3).
Attention
z
Turn screws clockwise in 2 locations, or at least in 1 location to be adjusted.
5) Little by little, turn the focus adjustment screws corresponding to the locations in
the table below counter clockwise and stop where the image is in focus (
page 55).
z
If the screws are turned counter clockwise, the tilt of the lens will change (see Figure 1) by moving the lens
mount bracket of the lens mounter forward (screen side), and in the projected image on the screen, the
adjustment screws and the focus point in the opposite direction will move from the inner side of the screen
to the outside.
6) Press the <SHIFT> button on the remote control or the <LENS> button on the control
panel to display the shift adjustment menu and reset the screen position of the
projected image on the screen surface back to an optimal state.
7) Perform focus adjustment again near the center of the screen and if it is still not
enough, ne tune the amount of rotation of the adjustment screws.
8) When adjustments have been made, securely tighten the loosened xed screws.
9) Adjust the focus again using the remote control.
z
Tool used: Hex driver or allen wrench (diagonal 2.5 mm (0.1"))
z
The allen wrench is included with the projection lens ET-D75LE6, ET-D75LE8.
Adjustment location:
Location where the just focus point of the
screen is in the inner side of the screen
Figure 3 Relationship between the adjustment location and adjustment screws
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DZ21KE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DZ21KE in the language / languages: English as an attachment in your email.

The manual is 17,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DZ21KE

Panasonic PT-DZ21KE User Manual - German - 190 pages

Panasonic PT-DZ21KE User Manual - German - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info